manualshive.com logo in svg

VESPA 946 E4 EMEA 2021, Руководство пользователя


Поделиться
Скачать
background image

Locking torques (N*m)

Intake manifold fixing screws

 

10.8 - 12.8

Crankcase - crankshaft

Splitting the crankcase halves

- Undo the eight crankcase coupling screws.

- Separate the crankcase halves while keeping the

crankshaft in one of these two halves.

- Only after the halves have been separated, can

the crankshaft be checked.

CAUTION

WHILE OPENING THE CRANKCASES AND REMOVING
THE CRANKSHAFT, CHECK THAT THE THREADED
SHAFT ENDS DO NOT INTERFERE WITH THE MAIN BUSH-
INGS. FAILURE TO OBSERVE THIS PRECAUTION CAN
DAMAGE THE MAIN BUSHINGS.

CAUTION

KEEP THE CRANKSHAFT IN ONE OF THE TWO HALVES
OF THE CRANKCASE WHEN SEPARATING IT. IF YOU FAIL
TO DO THIS, THE CRANKSHAFT MIGHT ACCIDENTALLY
FALL.

- Remove the gasket and be careful with the align-

ment dowels.

Inspecting the crankshaft components

N.B.

TO MEASURE WEAR LIMITS AND COUPLING CLEARANCES, SEE THE SPECIFICATIONS CHAP-
TER.

See also

Crankcase - crankshaft - connecting rod

Engine

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

ENG - 178

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

Jetson ARROW Manual preview
ARROW
Бренд: Jetson Страницы: 24
Abilize Ranger MS01077 Instruction Booklet preview
Ranger MS01077
Бренд: Abilize Страницы: 24
Smart Wheel SMARTkick X7 8.5" User Manual preview
SMARTkick X7 8.5"
Бренд: Smart Wheel Страницы: 10
JBM 53920 Manual preview
53920
Бренд: JBM Страницы: 36
EWheels Medical EW-M41 Instruction Booklet preview
EW-M41
Бренд: EWheels Medical Страницы: 18
D-FLY DRAGONFLY Driver Manual preview
DRAGONFLY
Бренд: D-FLY Страницы: 72
Dominator The Commander User Manual preview
The Commander
Бренд: Dominator Страницы: 8
Kettler Zero 8 Authentic Blue Manual preview
Zero 8 Authentic Blue
Бренд: Kettler Страницы: 80
Hudora 11066 Manual preview
11066
Бренд: Hudora Страницы: 12
KB REVO E3 Complete User Manual preview
REVO E3
Бренд: KB Страницы: 14
Zingo X300 User Manual preview
X300
Бренд: Zingo Страницы: 8
Nextreme TOURER 8.5 User Manual preview
TOURER 8.5
Бренд: Nextreme Страницы: 16
FREERIDER FR-168-3S Users Instruction Users Instruction Manual Users Instruction preview
FR-168-3S
Бренд: FREERIDER Страницы: 44
SHARKS RS01-1 Instruction For Operation And Maintenance preview
RS01-1
Бренд: SHARKS Страницы: 34
Yadea ENOX EBX37 User Manual preview
ENOX EBX37
Бренд: Yadea Страницы: 24
Scootix SPEED5000 Manual preview
SPEED5000
Бренд: Scootix Страницы: 16
Scooty EVO 2 Instruction Manual preview
EVO 2
Бренд: Scooty Страницы: 20
Scooter Wholesales 49cc 4 Stroke Gas Scooter Owner'S Manual preview
49cc 4 Stroke Gas Scooter
Бренд: Scooter Wholesales Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды