manualshive.com logo in svg

VESPA 946 E4 EMEA 2021, Руководство пользователя


Поделиться
Скачать
background image

Battery

To access the battery the central cover «

A

» must

be removed, undoing the retaining screws.

Then remove the support clamp «

B

» undoing the

retaining screws «

C

».

The battery is the electrical device requiring the

closest monitoring and most diligent maintenance.

WARNING

USED BATTERIES ARE HARMFUL FOR THE ENVIRON-
MENT. COLLECTION AND DISPOSAL SHOULD BE CAR-
RIED OUT IN COMPLIANCE WITH REGULATIONS IN
FORCE.

CAUTION

ELECTROLYTE CONTAINS SULPHURIC ACID: AVOID
CONTACT WITH EYES, SKIN AND CLOTHES. IN CASE OF
ACCIDENTAL CONTACT, RINSE WITH ABUNDANT WA-
TER AND CONSULT A DOCTOR.

CAUTION

IN ORDER TO AVOID DAMAGING THE ELECTRICAL SYS-
TEM, NEVER DISCONNECT THE WIRING WHILE THE EN-
GINE IS RUNNING. DO NOT TIP THE VEHICLE TOO MUCH
IN ORDER TO AVOID DANGEROUS LEAKAGE OF THE
BATTERY ELECTROLYTE.

To install a new battery:

-

 Place the battery in its housing.

-

 Connect the positive pole «

+

» first and then the

negative pole «

-

».

Chassis

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

CHAS - 280

Содержание 946 E4 EMEA 2021




























































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 946 E4 EMEA 2021

Zap ELECTRIC SCOOTER Owner'S Manual preview
ELECTRIC SCOOTER
Бренд: Zap Страницы: 22
E-Cells Super Monarch AWD 1500 Crown Installation & User Manual preview
Super Monarch AWD 1500 Crown
Бренд: E-Cells Страницы: 22
E-Wheels EW-M35 Instruction Booklet preview
EW-M35
Бренд: E-Wheels Страницы: 16
Razor 13100E-BL Owner'S Manual preview
13100E-BL
Бренд: Razor Страницы: 24
5th Wheel G1 User Manual preview
G1
Бренд: 5th Wheel Страницы: 18
Buggies4One RAMBLA Mk 1 User Manual preview
RAMBLA Mk 1
Бренд: Buggies4One Страницы: 23
Quantum Rehab Q6 Edge HD Specifications preview
Q6 Edge HD
Бренд: Quantum Rehab Страницы: 2
PEUGEOT SPEEDFIGHT 3 RS Brochure preview
SPEEDFIGHT 3 RS
Бренд: PEUGEOT Страницы: 1
PEUGEOT Looxor 100 cm3 Owner'S Manual preview
Looxor 100 cm3
Бренд: PEUGEOT Страницы: 15
PEUGEOT 102 SPB-U2 Owner'S Manual preview
102 SPB-U2
Бренд: PEUGEOT Страницы: 28
Dominator Sniper Rider'S Manual preview
Sniper
Бренд: Dominator Страницы: 8
B+B Centuro Assembly Instructions Manual preview
Centuro
Бренд: B+B Страницы: 7
Lambretta 150 ld User Manual preview
150 ld
Бренд: Lambretta Страницы: 68
Tank TK50QT-15 User Manual preview
TK50QT-15
Бренд: Tank Страницы: 18
Roma Medical Tulsa S245 User Manual preview
Tulsa S245
Бренд: Roma Medical Страницы: 20
SCOOT AND RIDE My First Instruction Manual preview
My First
Бренд: SCOOT AND RIDE Страницы: 73
INOKIM QUICK4 User Manual preview
QUICK4
Бренд: INOKIM Страницы: 11
OCEAN DRIVE S9 Instruction Manual preview
S9
Бренд: OCEAN DRIVE Страницы: 94

Бренды по названию

Популярные бренды

Загрузить еще бренды