VESPA 946 E4 EMEA 2021 Скачать руководство пользователя страница 119

Страница: 119 / 283

ABS GROUND

1. Ne - Ground

Diagnostic instrument

STARTER COMMAND

Function

Commands engine starting through the injection control unit.

Operation / Operating principle

The starter button, the brake switches, the starter command relay and the injection control unit between

PIN 5 and 10 are involved.

ELECTRICAL ERRORS

Starter command P0170

- shorted to positive.

Error cause

Short-circuit to positive: excessive voltage at PIN 10 of the control unit connector.

Troubleshooting

Short-circuit to positive:

- This malfunction is detected with a brake activated and the starter button pressed (voltage of 12V read

at PIN 5)

- If the battery voltage does not drop (thanks to the absorption of the starter command relay excitation

coil) the control unit understands that PIN 10 is shorted to battery.

- Restore the cabling (if the short is in the cabling) or the relay (if the short is in the relay).

ENGINE TEMPERATURE SENSOR

Function

Serves the purpose of communicating the engine

temperature to the control unit in order to optimise

performance.

Operation / Operating principle

NTC type sensor (resistance sensor, inversely

variable with temperature).

Pin-out:

Vespa 946 E4-E5 EMEA-USA-ASIA (2021-)

Electrical system

ELE SYS - 119

Содержание 946 E4 EMEA 2021




























































































































































































































































































Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды

VESPA 946 E4 EMEA 2021, Руководство пользователя

Результаты поиска

Содержание 946 E4 EMEA 2021

Отзывы:

Похожие инструкции для 946 E4 EMEA 2021

Бренды по названию

Популярные бренды