![background image](http://html1.mh-extra.com/html/vem/vemodrive-vsi-2-0-hd/vemodrive-vsi-2-0-hd_instruction-manual_3985886082.webp)
80
Functional Description
CG Drives & Automation, 01-5326-01r3b
11.2.3 Mains supply voltage [21B]
In this menu the nominal mains supply voltage connected to
the AC drive can be selected. The setting will be valid for all
parameter sets. The default setting, Not defined, is never
selectable and is only visible until a new value is selected.
Once the supply voltage is set, this selection will not be
affected by the Load Default command [243].
Brake chopper activation level is adjusted using the setting
of [21B].
Communication information
11.2.4 Motor Data [220]
In this menu you enter the motor data to adapt the AC drive
to the connected motor. This will increase the control
accuracy as well as different read-outs and analogue output
signals.
5IF
AC drive can control both
Asynchronous motors and PMSM-Permanent magnet
synchronous motor select type of motor in menu [22I].
Motor M1 is selected as default and motor data entered will
be valid for motor M1. If you have more than one motor
you need to select the correct motor in menu [212] before
entering motor data.
Motor Voltage [221]
Set the nominal motor voltage.
WARNING!
This menu must be set according to the AC
drive product label and the supply voltage
used. Wrong setting might damage the AC
drive or brake resistor.
NOTE: The setting is affected by the “Load from CP”
command [245] and if loading parameter file via
VEMo
SoftCom.
Default:
Not defined
Not Defined 0
Inverter default value used. Only valid if
this parameter is never set.
220-240 V
1
Only valid for
VSI2.0 HD 400/500V
380-415 V
3
Only valid for
VSI2.0 HD 400/500/690V
440-480 V
4
Only valid for
VSI2.0 HD 400/500/690V
500-525 V
5
Only valid for
VSI2.0 HD 500/690V
550-600 V
6
Only valid for
VSI2.0 HD 690V
660-690 V
7
Only valid for V
SI2.0 HD 690V
Modbus Instance no/DeviceNet no:
43381
Profibus slot/index
170/30
EtherCAT index (hex)
4d35
Profinet IO index
19765
Fieldbus format
UInt
Modbus format
UInt
21B Supply Volts
Stp
Not defined
WARNING!
Do not work on a drive when a rotating
PMSM- permanent magnet motor is
connected to it. A rotating PMSM motor
energizes the drive including its power
terminals.
NOTE 1: The parameters for motor data cannot be
changed during run mode.
NOTE 2: The default settings are for a standard 4-pole
motor according to the nominal power of the AC drive.
NOTE 3: Parameter set cannot be changed during run if
the parameter set is set for different motors.
NOTE 4: Motor Data in the different sets M1 to M4 can
be revert to default setting in menu “[243] Default>Set”.
WARNING!
Enter the correct motor data to prevent
dangerous situations and assure correct
control.
Default:
400 V for
VSI2.0 HD 400V
500 V for
VSI2.0 HD 500V
690 V for
VSI2.0 HD 690V
Range:
100-700 V
Resolution
1 V
NOTE: The Motor Volts value will always be stored as a 3
digit value with a resolution of 1 V.
221 Motor Volts
Stp
M1:
400V
9(0R'ULYH 96, 9(0 U
Содержание VEMoDRIVE VSI 2.0 HD
