Velocity PHTM2080H Скачать руководство пользователя страница 77

Страница: 77 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Troubleshooting

(continued)

Table 18-5: Active Fault Code and Corrective Actions (continued)

Detailed Fault Code found on "

" and "

" menus in brackets, e.g. [

Code

Name

Possible Cause

Corrective Action

H04
E04

Supply

High Limit

Air in system.

Verify the system is full of water and the air has been

properly purged. Cycle boiler power to initiate pump air

elimination function. Air is removed from boiler loop when

there are no "air noises" in the heat exchanger.

System pump, thermostat, zone

valve or panel problem.

Check pump operation, replace if necessary. Ensure each

zone demand produces expected pump, zone valve, and

boiler response.

Piping problem.

Verify the boiler is piped properly to heating system. See

recommended piping diagram. Repair piping to meet

requirements as required.

Boiler pump problem.

Check boiler differential temperature (supply-return) at

maximum fire. Check piping and boiler pump if differential

temperature is too high. Verify boiler pump is running.

Check T5.0 A fuse (Figures 19-1 and 19-2), replace if

necessary. Replace pump if necessary.

Heating load at time of error

below minimum firing rate of

boiler.

Test individual zones and ensure proper zone sizes.

Header sensor not sensing

temperature.

(Boiler is multiple boiler slave

or modulating based on header

sensor)

Check header sensor installation;

• Strap on - use heat conductive grease and insulate.

• Thermowell - ensure inserted fully.

Check header sensor temperature is close to and tracks

with supply sensor. If difference greater than 5ºF (3ºC),

move header sensor to location to better sense boiler

water temperature.

H05
E05

Low

Water

Flow

Air in system.

Verify the system is full of water and the air has been

properly purged.

Cycle boiler power to initiate pump air elimination function.

Air is removed from boiler loop when there are no "air

noises" in the heat exchanger.

Piping problem.

Verify the boiler is piped properly to heating system. See

recommended piping diagram. Repair piping to meet

requirements as required.

Boiler pump problem.

Verify boiler pump is running. Check T5.0 A fuse (Figures

19-1 and 19-2), replace if necessary. Replace pump if

necessary.

Boiler flow switch defective.

Check boiler flow switch, switch wiring and controller input.

Flow restriction or clogged

strainer.

Verify there are no restrictions and clean strainer if present.

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды