Velocity PHTM2080H Скачать руководство пользователя страница 84

Страница: 84 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Troubleshooting

(continued)

Table 18-6: Detailed Fault Code (found on"

" and "

" menus, continued)

Code Detailed

Code

Type

Condition

H17
E17

H17

Hold

Control in program mode.

H17

Hold

Internal Safety Core error.

E17

Lockout

Parameter CRC error.

E17

Lockout

Parameter CRC error.

H17

Hold

Boiler Type and BCC mismatch.

E17

Lockout

Parameter value read from safety core differs from value read in application MCU.

H17

Hold

Safety core refused write of fuel selection parameter.

H17

Hold

Parameter transfer from a new BCC is required or in progress.

E17

Lockout

BCC is missing, has incompatible software revision or is damaged.

H18
E18

E18

Lockout

Application parameters are not valid, normal condition following a new parameter

download.

H18

Hold

Actual boiler model doesn't match with control detected model during factory reset.

H18

Hold

CH Setpoint and Modulation source both selected.

H18

Warning

Invalid header sensor configuration.

H18

Hold

Invalid Stepped modulation parameters (Start Offset-Recycle Limit)<5°F.

H18

Warning

Invalid Setpoint interpolation parameters.

H18

Hold

Invalid Recirc (Comfort) Mode configuration.

E18

Lockout

Selected boiler model default parameters not available.

H18

Hold

Boiler pump output parameter set to "Disabled" or boiler pump output set to "Boiler

Pump CH, Off for DHW" and Auxiliary pump outlet is not set to "DHW Boiler Piped

IWH".

E19

Lockout

Air/Fuel ratio outside acceptable limit.

H20
E20

H20

Warning

Fuel valve or blower demand outside limit.

E20

Lockout

Ionization current too low during calibration.

E20

Lockout

Ionization current too high during calibration.

E20

Lockout

Ionization current lies outside the permissible range during calibration (deviation

from previous level too great).

E20

Lockout

Calibration result invalid.

H21
E21

H21

Hold

Ionization current lies outside the permissible range.

H21

Hold

Gas Valve offset adaption at limit.

E21

Lockout

Ionization current too high/low after repeated start.

E21

Lockout

Gas valve current fault.

H22
E22

H22

Hold

No flame build up at burner start.

E22

Lockout

No flame build up at burner start.

H23
E23

E23

Lockout

A flame was detected before burner start.

E23

Lockout

A flame is detected for 15s, although a valve has been switched off.

H23

Hold

Flame amplifier fault.

E23

Lockout

Flame amplifier fault.

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды