Velocity PHTM2080H Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 104

background image

2

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

The following terms are used throughout this manual to bring attention to the presence of hazards of various
risk levels, or to important information concerning product life.

The Massachusetts Board of Plumbers and Gas Fitters has listed the Phantom II Boiler. See the Massachusetts

Board of Plumbers and Gas Fitters website for the latest Approval Code or ask your local Sales Representative.
The Commonwealth of Massachusetts requires this product to be installed by a licensed Plumber or Gas fitter.

NOTICE:

Indicates special instructions on

installation, operation, or service which are

important but not related to personal injury

hazards.

DANGER

Indicates a hazardous situation

that, if not

avoided, will result in death or serious injury.

CAUTION

Indicates a hazardous situation

that, if not

avoided, could result in minor or moderate

injury.

WARNING

Indicates a hazardous situation

that, if not

avoided, could result in death or serious injury.

DANGER

Explosion Hazard.

DO NOT store or use gasoline or other flammable vapors or liquids in the vicinity of

this or any other appliance.
If you smell gas vapors, DO NOT try to operate any appliance - DO NOT touch any electrical switch or

use any phone in the building. Immediately, call the gas supplier from a remotely located phone.

Follow the gas supplier’s instructions or if the supplier is unavailable, contact the fire department.

WARNING

This boiler must only be serviced and repaired by qualified installer, service agency or gas supplier.

• If any controls are replaced, they must be replaced with identical models.

• Read, understand and follow all the instructions and warnings contained in all the sections of this

manual.

• If any electrical wires are disconnected during service, clearly label the wires and assure that the wires

are reconnected properly.

• Never jump out or bypass any safety or operating control or component of this boiler.

• Assure that all safety and operating controls and components are operating properly before placing

the boiler back in service.

• Annually inspect boiler.

• Annually inspect all vent gaskets and replace any exhibiting damage or deterioration.

!

!

!

!

!

«
1
2
3
4
...
»

Содержание PHTM2080H









































































































Отзывы:

Нет отзывов

Похожие инструкции для PHTM2080H

Бренд: IBC Страницы: 4

Бренд: IBC Страницы: 6

Бренд: IBC Страницы: 74

Бренд: ideal commercial Страницы: 6

Infinity Energy 2

Бренд: RBI Страницы: 164

Бренд: Raypak Страницы: 64

Compact HRE 18 OV

Бренд: Intergas Страницы: 48

turboMAX plus 2 E Series

Бренд: Vaillant Страницы: 52

Бренд: Viessmann Страницы: 32

Бренд: Radiant Страницы: 20

Бренд: eta Страницы: 92

Бренд: Biasi Страницы: 88

Бренд: Radijator Страницы: 32

GOLD CGS 550-110-260/0107

Бренд: Weil-McLain Страницы: 64

Бренд: Riello Страницы: 196

Бренд: ENERGY KINETICS Страницы: 2

Бренд: Ravenheat Страницы: 52

Бренд: Calomax Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды