Velocity PHTM2080H Скачать руководство пользователя страница 54

Страница: 54 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Status Screen Display

Description

Priority:

Standby

Status:

Standby

Burner -

Off

Pump(s) -

Off

There is no call for heat, boiler is not firing and priority is "

standby

". Boiler is ready to

respond to a call for heat. Additionally, boiler and pumps remain off when Warm Weather

Shut Down is active or "Boiler Switch" (

A01

) is set to "Off".

Priority:

Standby

Status:

Pump Purge

Burner -

Off

Pump(s) -

Cycle

Pump Air Elimination (Pump Purge) is entered when power is cycled or when there has

been a supply high limit hold. During this state boiler pump cycles on and off every

5 seconds for two minutes to help remove air from boiler water piping. This may be
interrupted by pressing "

reset

" button.

Priority:

Central Heat

Status:

Standby

Burner -

Off

Pump(s) -

Cycle

Boiler is not firing. There is a CH demand and supply temperature is greater than setpoint

minus "Diff Below".

Priority:

Central Heat

Status:

Prepurge

Burner -

Off

Pump(s) -

When supply temperature drops, burner demand continues with following status shown:

Waiting For Limit To Close

: blower started, air pressure switch is checked.

Prepurge

: blower is driven to prepurge speed to empty chamber of flue products.

Priority:

Central Heat

Status:

Burner Ignition

Burner -

Pump(s) -

After prepurge is complete following status is shown:

Burner Ignition

: Spark and fuel valve are energized.

Priority:

Central Heat

Status:

Calibration

Burner -

Pump(s) -

After burner is started, a Calibration is initiated due to

1. Power Cycle 2. Periodic requirement

Calibration

: after blower reaches calibration speed setting, ionization setpoint is

calibrated, next blower drives to low fire and fuel valve output is calibrated (runs for 1

minute).

Priority:

Central Heat

Status:

Run

Burner -

Pump(s) -

After burner ignition (following calibration), the following status is shown:

Low Fire Hold

: modulation rate held at low fire to allow initial home heating

Run

(Modulate): Burner rate modulates to match home heat requirements.

Priority:

DHW

Status:

Run

Burner -

Pump(s) -

If CH demand is active and a DHW demand is received, DHW demand becomes "priority"

and modulation rate, setpoint, "Diff Above" and "Diff Below" are based on DHW settings.

Priority:

Standby

Status:

Post-purge

Burner -

Off

Pump(s) -

Off

If there is no call for heat, fuel valve is closed and blower is driven to post-purge speed to

empty combustion chamber of flue products.

Priority:

Standby

Status:

Hold

Burner -

Off

Pump(s) -

Off

Hold status is entered when a delay is needed before allowing burner to fire. See user

display door label or section 18 Troubleshooting to determine cause of the Hold.

Priority:

Standby

Status:

Lockout

Burner -

Off

Pump(s) -

Off

A lockout status is entered to prevent boiler from running due to a detected problem. See

user display door label or section 18 Troubleshooting to determine cause of Lockout. Last

8 Lockouts are recorded in Lockout History.

Table 14-10: Boiler Sequence of Operation

Start-Up and Checkout

(continued)

Boiler Sequence of Operation

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды