Velocity PHTM2080H Скачать руководство пользователя страница 64

Страница: 64 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

1. Boiler Control

Control simultaneously modulates blower speed

and gas valve position to control firing rate and

sequences up to three pumps to respond to DHW

and CH demands.

2. Flame Supervision/Air-Fuel Ratio Control

Control is a "Gas-Adaptive system" that regulates

air and gas flow mixture by measuring flame

ionization and adjusting gas valve to achieve

target air fuel ratio. This eliminates need to make

throttle screw or offset adjustments. This system is

self-calibrating and continuously maintains air fuel

ratio at desired value.

3. Domestic Hot Water

When there is a DHW demand, system pump

will operate per

P01

setting. Priority protection

is provided to ensure heating system is also

serviced.

4. Central Heat

CH demand is detected by a heating thermostat

call for heat. When CH demand is detected,

control starts boiler pump and modulates firing

rate based on measured supply sensor and CH

setpoint. Control can accept a second heating

thermostat wired to the Aux T'stat input. CH

demands have separate setpoint and maximum

modulation rates.

5. Sensorless Reset

Control system monitors recent firing rate and

burner cycle data to infer current building heat

loss. Target supply water temperature is then

adjusted to match this heat load. No outdoor

sensor mounting or wiring is required. Boost

feature increases operating temperature setpoint

by 10°F (5.6°C) every 20 minutes CH demand

is not satisfied. This process will continue until

heat demand is satisfied (indoor air is at desired

temperature), or CH setpoint is reached. Once

heat demand is satisfied, operating setpoint

reverts to value determined by the Outdoor Reset

settings.

6. Pump Exercise

Connected pumps are automatically run for a 20

second exercise period after not being used for

longer than 7 days. This helps prevent pump rotor

seizing.

7. Pump Air Elimination (Pump Purge)

Pump purge is entered when power is cycled

or when there has been an over temperature

hold. During this state boiler pump cycles on

and off every 5 seconds for two minutes to help

remove air from boiler water piping. This may be
interrupted by pressing the

reset

button.

8. Built-in Safety Control

Control includes functions designed to ensure

safe and reliable operation. In addition to flame

supervision, control monitors supply water

temperature, differential water temperature, and

flue temperature safety limits. Boiler modulation

is adjusted when required to help avoid loss

of boiler operation due to exceeding limits.

Additionally, control accepts field installation of

external limits.

9. Fuel Conversion

The conversion from Natural Gas to LP Gas (or

vice versa) is made by changing gas valve setting

and a control parameter change on display.

10. Plug & Play” Multiple Boiler Control Sequencer

When multiple boilers are installed, the Control’s

Sequencer may be used to coordinate and

optimize the operation of up to eight (8) boilers.

Boilers are connected into a “network” by simply

“plugging in” standard ethernet cables into each

boiler’s “Boiler-To-Boiler Communication” RJ45

connection.

11. Priority Demand

Control accepts a call for heat from multiple

places and responds to its "Priority". When more

than one demand is present, higher priority

demand is used to determine active boiler

settings. For example, when DHW has priority,

setpoint, "Diff Above", "Diff Below" and pump

settings are taken from DHW selections. Active

"Priority" is displayed on the Diagnostic Menu,

item "

CO2

", see Table 15-9.

Control System Overview

The control manages all of the following boiler

functions:

Operation

(continued)

NOTICE:

This section covers control features available via local display. For additional control features available

via our App, see Extended Features manual available on our website or in our App.

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды