Velocity PHTM2080H Скачать руководство пользователя страница 43

Страница: 43 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Field Wiring

DANGER

Electrical Shock Hazard.

•

Disconnect electrical supply before

installing or performing maintenance.

• Electrical power may be supplied

from more than one circuit.

•Lock out all electrical boxes with padlock once

power is turned off.

WARNING

Electrical Shock Hazard.

All wiring and grounding must conform to

requirements of authority having jurisdiction or,

in absence of such requirements, to National

Electrical Code/NFPA 70 or Canadian Electrical

Code, Part 1 (CSA C22.1 - latest edition).

•

Make electrical connections according

to boiler's wiring diagram and instructions.

Failure to properly wire electrical connections

to the boiler may result in severe personal

injury, death or substantial property damage.

•

Protect each boiler circuit with a

properly sized over-current device.

•

Never jump out or bypass any safety or

operating control or component of this boiler.

NOTICE:

Internal wiring diagrams contained in

this manual are for reference only. Each boiler is

shipped with a wiring diagram sheet within boiler

literature packet. Read, understand and follow this

wiring diagram and wiring diagrams of any field

supplied controls.

NOTICE:

Boiler is equipped with a UL 353 listed

high water temperature limit. This limit provides

boiler shutdown in event boiler water temperature

exceeds setpoint of control. Certain local codes

require an additional water temperature limit. If

necessary, install an additional water temperature

limit (Honeywell L4006 Aquastat). Wire as

indicated in Figure 12-3.

Locating Field Connection Terminal Strips

Field connection terminal strip locations are shown in
Figure 12-1. To access terminal strips:
1. Remove front door. Front door is removed by

first loosening two thumb screws located

under front of door.

2. Disconnect igniter wire at burner door.
3. Pull control enclosure forward, then to the left and

allow it to swing down into the service position.

Figure 12-1: Location 120 VAC and Low Voltage

Connection Boards

Field 120 VAC Connections

1. Provide a dedicated circuit for boiler of 15A

or greater. A service switch is recommended

and is required by many local codes.

Locate this switch in accordance with local codes

or, in absence of such requirements, in a location

where it can be safely accessed in an emergency.

2. All 120 VAC connections to boiler are made on

120 VAC Connections terminal strip (see Figure

12-2) located on right side of bottom panel. Route

all 120 VAC wiring through conduit knock out

holes located on right side in front of terminal strip.

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды