Velocity PHTM2080H Скачать руководство пользователя страница 72

Страница: 72 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Troubleshooting

WARNING

Electrical Shock Hazard.

Turn off power to boiler before working on wiring.

A. Troubleshooting with No Active Fault Code Displayed

Table 18-1: Troubleshooting with No Active Fault Code

Indication

Possible Causes

Corrective Action

Display Completely

Dark And Fan Off

No 120 VAC supplied to boiler.

Check breaker and wiring between breaker panel and

boiler.

Display Completely

Dark, Fan Running

Blown T1.0 A Fuses (supplies power

to control).

Check T1.0 A Fuse, replace with a 1 Amp, 250V, Slow

Blow, 5 x 20 mm if necessary.

Loose low voltage blower wiring.

Check low voltage blower wiring connections.

Control damaged.

Replace control.

Boiler Not

Responding To

Call For Heat,

Icon Is Off

A01

Boiler On/Off Switch is "Off",

(Status

StA13

Switch Quick Menu Item

A01

, Boiler On/Off Switch,

"On".

Remote thermostat is satisfied, loose

thermostat wiring.

Check remote thermostat setting and wiring.

Blown T0.5 A Fuse (supplies power

to thermostats).

Check T0.5 A Fuse, replace with a 0.5 Amp, 250V,

Slow Blow, 5 x 20 mm if necessary.

Boiler Not

Responding to Call

For Heat,

Icon is On

Boiler is in standby, (Status

StA 1

temperature is above setpoint.

Check temperature setpoint setting.

Faucet icon is on

Servicing DHW demand.

Boiler is in Warm Weather Shutdown,

(Status

StA 14

Feature not available with local user display.

Boiler Running But

System Or Auxiliary

Pump Not Running

Pump setting is incorrect.

Switch

Menu Item

P01

, System Pump Selection.

Refer to Table 15-15.

Loose wiring to pump

Check pump wiring.

Pump damaged.

Replace pump.

Boiling, Kettling, or

Water Hammer

Air in system piping.

Cycle power to boiler to initiate an air elimination

cycle to help remove air from boiler water.

Low system water pressure.

Check boiler water pressure, adjust feedwater as

required.

Rough ignitions

Gas pressure problem.

Refer to Table 3-5 for required pressure range.

Dirty/damaged burner.

Refer to Section 17 Service and maintenance for

proper procedure to check burner. Replace if

necessary.

Dirty/damaged ignitor/flame sensor.

Refer to Section 17 Service and Maintenance for

proper procedure to check ignitor/flame sensor.

• Check spark gap and ignitor/flame sensor distance

to burner. Replace if necessary.

Relief Valve

Opening

System pressure exceeds relief

valve setting.

Lower system pressure below rating of supplied

safety relief valve.
Replace standard safety relief valve with higher

rated valve up to the maximum pressure of the heat

exchanger. 50 psig (345 kPa)
Improperly sized expansion tank.

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды