Velocity PHTM2080H Скачать руководство пользователя страница 49

Страница: 49 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Start-Up and Checkout

(continued)

DANGER

Explosion Hazard.

Do not use matches, candles, open flames or

other ignition source to check for leaks. Failure

to comply could result in severe personal injury,

death or substantial property damage.

6. If required, please proceed with fuel conversion

and altitude conversion. Otherwise, skip to final

check continued.

5. Check all gas piping before boiler manual shut-off

valve for leaks and purge sections that are filled

with air. Refer to NFPA 54/ANSI Z223.1

National

Fuel Gas Code

and/or CAN/CSA B149.1

Natural

Gas and Propane Installation Code

for additional

information on testing and purging gas lines.

Figure 14-1: Manual Air Vent Location

Flame Rod

Detail A

(Scale 2:1)

Manual Air Vent

Confirm 1/4" ID
tubing is connected
to hose barb. Route
tubing to a safe place
away from controls
before opening vent.

A. Use 1/4 in. (6 mm) ID tubing connected to

hose barb and route tubing to a safe draining

location.

B. Turn vent counter clockwise and allow heat

exchanger to vent until a steady stream of

water is observed.

C. Close vent and remove hose.

5. Isolate each zone to purge air confirming that

heating system and boiler are completely filled.

3. Inspect all wiring for loose, uninsulated or

miswired connections.

4. Verify boiler and system are full of water and

pressurized.

NOTICE

: When boiler is first powered, control will

automatically run a pump purge sequence (status 10)

for 2 minutes.

Final Check Before Starting Boiler

WARNING

Asphyxiation Hazard. Burn Hazard.

Completely read, understand and follow all

instructions in this manual before attempting

start-up.

1. Verify that venting, water piping, gas piping and

electrical system are installed properly.

2. Confirm vent system is complete and free of

obstructions before attempting to fire boiler.

NOTICE

: Boiler is shipped from factory configured

for Natural Gas (NG) 0-2,000 ft. (0-610 m).

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды