Velocity PHTM2080H Скачать руководство пользователя страница 71

Страница: 71 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

WARNING

Component Damage.

Do not over tighten burner door mounting nuts.

Doing so could break burner door mounting

studs. If any of these studs is damaged, heat

exchanger must be replaced. Use of a short 10

mm box wrench will reduce risk of damaging

these nuts.

Service and Maintenance

(continued)

Figure 17-5: Condensate Trap Exploded Parts View

Condensate Tube
from heat exchanger

Condensate
Trap Vent

Condensate Trap

Ball Float

Float
Support
Gasket

Float
Support

Cleanout
Cap O-Ring

Cleanout
Cap

Cleanout
Cap Nut

Trap Vent
(bottom panel)

NOTICE:

Attempting to clean heat exchanger

or trap with anything other than water or vinegar

could damage heat exchanger or result in

condensate backup, causing boiler to shut down.

10.

Reinstall burner door/blower assembly.

Follow above steps in reverse order.

11.

Inspect vent system.

A. All gaskets and joints between boiler heat

exchanger and terminal are leak tight.

B. All supports are intact and vent system is

properly pitched.

C. All pipe is in good condition. Look for

damage such as cracks, heat distortion,

and embrittlement. If any such damage is

found, pipe must be replaced and cause of

damage identified.

D. Vent/air terminals are in good condition,

free from blockage and still correctly

located relative to doors, windows, decks, etc.

E. Refer to Sections 7 thru 9 to re-assemble

any vent system components that are

disassembled during this inspection and for

details on supporting, pitching and

terminating vent system.

12.

Inspect hydronic system.

A. Look for leaks and repair if found. If system

contains antifreeze, or other additives, test

and/or maintain them as directed by additive

manufacturer.

B. Test heating system water quality to ensure

they meet minimum requirements specified

in Section 14 Start-Up and Checkout.

C. Refer to Appendix B for important information

on quality and boiler additives.

13.

Inspect safety relief valve.

WARNING

Explosion Hazard.

Safety relief valves require periodic

maintenance. Refer to relief valve

manufacturer's instructions for frequency and

proper procedure. Any testing or maintenance

shall be done by a qualified installer, service

agency or gas supplier.

14.

Place boiler back into operation.

A. Replace any wiring which has been

disconnected.

B. Perform visual inspection of gas piping

to ensure no inadvertent damage to gas train

components during servicing.

C. Follow all instructions in Section 14 Start-Up

and Checkout to place boiler back in service,

including performance of combustion test.

15.

Test boiler flow switch.

A. Start with boiler in standby.

B. Close a shut off valve in boiler loop.

C. Initiate a call for heat and confirm that boiler

shows an Active Fault (

H05

) indicating flow

switch is open.

WARNING

Component Damage.

If burner comes on with no flow through boiler,

there is a problem with flow switch. Turn boiler

off immediately. Failure to do so could result in

severe heat exchanger damage.

16.

Assure that all safety and operating controls

and components are operating properly before
placing boiler back in service

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды