Velocity PHTM2080H Скачать руководство пользователя страница 62

Страница: 62 / 104

110332-04 - 2/23

PHTM II

Installation, Operating & Service Instructions

Operation

(continued)

Table 15-15: Menu

, Pump Menu (visible only after password entered)

Default

Range/

Choices

Parameter and Description

1, 2, 3

P01

System Pump Output Select:

Activates System Pump output according to selected function.

(1)

System Pump Any

Demand:

Pump Runs during any call for heat.

(2)

System Pump Central

Heat:

Pump Runs during CH1 and CH2 demand. Pump does not

start for a DHW demand and will be forced off if there is a DHW

demand and DHW Priority is active.

(3)

Zone 1 Pump, CH Zone 1

Only:

Pump runs during CH1 demand. Pump does not start for CH2

or DHW demand. Pump will be forced off when DHW priority is

active. This option allows System Pump output to be used as a

zone pump.

1, 2, 3

P02

Boiler Pump Output Select:

Activates Boiler Pump output according to selected function.
(1)

Boiler Pump Any Demand: Pump runs during any call for heat. Pump also runs when it is

Sequencer lead pump.

(2)

Boiler Pump Header

Sensor Demand:

Pump runs when boiler is firing and when there is a DHW heat

demand. Selected when Header Sensor is selected as CH1 and

CH2 modulation sensor, and boiler is a stand-alone boiler.

(3)

Boiler Pump CH Only, Off

for DHW:

Pump runs during CH1, CH2 and CH frost protection demand

and will be forced off if there is a DHW demand and DHW

priority is active. This function is selected when there is a direct

piped IHW installed with a dedicated DHW pump.

1, 2, 3, 4

P03

Auxiliary Pump Output Select

Activates Auxiliary Pump output according to selected function.
(1)

Recirculation Pump:

Combi boilers only.

(2)

DHW Pump Primary Loop

Piped IHW:

Pump runs during DHW demand. DHW Priority enable/disable

does not affect pump operation.

(3)

DHW Pump Boiler Piped

IHW:

Pump runs during DHW demand. Pump is forced off during CH

demand when 1) DHW priority is disabled or 2) DHW priority

is enabled and DHW demand has remained on for longer than

Priority Time.

(4)

Zone 2 Pump CH Zone 2

Only:

Pump runs during CH2 call for heat. Pump does not start for

CH1 or DHW demand. The pump will be forced off when DHW

priority is active. This allows the Aux Pump output to be used as

a zone pump.

Содержание PHTM2080H









































































































Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды

Velocity PHTM2080H, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание PHTM2080H

Отзывы:

Похожие инструкции для PHTM2080H

Бренды по названию

Популярные бренды