background image

Chapter 9 Troubleshooting and Countermeasures 

 

  ACH200 Series High Voltage Variable Frequency Speed Control System Operating Manua

 

131 

 

Chapter 9 Troubleshooting and 

Countermeasures

 

There are two types of messages that appear under abnormal conditions in a variable frequency 

speed control system, one is an alarm message and the other is a fault message. When there is an 

alarm, the system can still continue to work, but will light up the alarm indicator and trigger an 

audible  and  visual  alarm.  When  a  fault  occurs,  the  system  will  automatically  shut  down,  while 

lighting  the  fault  indicator  and  triggering  an  audible  and  visual  alarm.  Only  after  the  fault  is 

completely removed and the "Fault Reset" button is pressed, the fault can be removed and the system 

can be turned on again. All alarms and faults are recorded in the information system and can be 

viewed by clicking on the "History" button.

 

9.1 Safety Precautions

 

Warning

 

●This product carries a dangerous voltage and it controls a potentially dangerous 
motion  mechanism.  Failure  to  comply  with  the  regulations  or  operate  it  in 
accordance with the requirements of this manual may result in personal injury or 
death, damage to the product and associated systems.

 

●Only trained professionals are allowed to operate this product, and before using 
this  product,  be  familiar  with  all  the  safety  instructions  and  regulations  of 
operation  in  this  manual;  proper  operation  and  maintenance  is  a  reliable 
guarantee to achieve safe and stable operation of this product.

 

●Do not perform wiring work while the power is on, otherwise there is a risk of 
death by electric shock; when wiring, inspection, maintenance, etc., cut off the 
power to all associated equipment and make sure the DC voltage of the main 
circuit has dropped to a safe level, and wait 5  minutes  before performing the 
relevant work.

 

Attention

 

●Prevent  children  and  the  public  from  coming  in  contact  with  or  near  this 
product.

 

●This product can only be used in accordance with the manufacturer's specified 
purpose  and  may  not  be  used  in  special  areas  related  to  emergency,  rescue, 
marine, medical, aviation, nuclear facilities, etc. without permission.

 

●Unauthorized  modifications,  use  of  parts  not  sold  or  recommended  by  the 
manufacturer of this product may result in malfunction.

 

Important

 

●Be sure to deliver this manual to the actual user to ensure that the actual user 
reads it carefully before using it.

 

●Please make sure you read and fully understand these safety rules and warning 
signs before installing and commissioning the AC drive.

 

9.2 Fault, Warning, Alert Code Types

 

● When the operation of the AC drive or motor is abnormal, please first confirm the code and 

Содержание ACH200 Series
















































































































































Отзывы: