Veichi ACH200 Series Скачать руководство пользователя

Страница: 33 / 143

Chapter 3 Mechanical and Electrical Installation

ACH200 Series High Voltage Variable Frequency Speed Control System Operating Manual

4) Open all cabinet doors and carefully inspect the frequency control system and its

accompanying equipment for possible transport damage. If any parts are damaged or missing,

please contact our technical service department immediately. Please note the way in which the

cabinet doors are opened.

5) Check if the cabinet doors can be opened and closed completely, if not, the cabinet needs to be

adjusted. Check the limit switch on the door: after power up the front door and back door of

the cabinet cannot be opened except for the front door of the control cabinet. If the cabinet door

is opened illegally the system will alarm.

6) Fine tune the cabinets and fasten the adjacent cabinets using the fastening bolts.

7) Connect the wiring inside the cabinet, as well as install and fix the power unit under the

guidance of our professional staff.

Note: Please note the method of opening the cabinet door, do not force the door open, otherwise

the unit will be damaged.

3.2.6 Installation of The Cabinet Top Fan

Depending on the model, the ACH200 series high voltage AC drives are fitted with different

numbers of fans to allow for heat dissipation. Some models are shipped with the cabinet top fan

already installed, some models are shipped with the cabinet top fan in a separate package and need

to be installed and fastened by the user on site as shown in the diagram below.

A total of 8 bolts (M6*16) on the left and right edges of the fan, as shown in the diagram below:

Figure.3-8

Содержание ACH200 Series
















































































































































Результаты поиска

Содержание ACH200 Series

Отзывы:

Похожие инструкции для ACH200 Series

Бренды по названию

Популярные бренды

Veichi ACH200 Series, Руководство пользователя

Результаты поиска

Содержание ACH200 Series

Отзывы:

Похожие инструкции для ACH200 Series

Бренды по названию

Популярные бренды