VAT 650 GS Series Скачать руководство пользователя

Страница: 52 / 77

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

52/77

Command

Acknowledgement

(within 10ms after reception of command)

Setup function

Description

Set [s:04][abcdefgh][CR][LF]

[s:04][CR][LF]

Get [i:04][CR][LF]

[i:04][abcdefgh][CR][LF]

VALVE

CONFIGURATION

data length 3 characters

valve position after power up:

0 = closed, 1 = open

valve position after power failure: 0 = closed, 1 = open

0 (reserved, do not change)

This function does the valve configuration.

Set [s:01][abcdefgh][CR][LF]

[s:01][CR][LF]

Get [i:01][CR][LF]

[i:01][abcdefgh][CR][LF]

SENSOR

CONFIGURATION

data length 8 characters

0 = no sensor

1 = 1 sensor operation (sensor 1 input)

2 = 2 sensor operation with automatic changeover

(low range = sensor 2 input, high range = sensor 1 input)

= 1 sensor operation (sensor 2 input)

= 2 sensor operation with automatic changeover

(low range = sensor 1 input, high range = sensor 2 input)

Note: Sensor operation modes 2, 3 and 4 are possible with 2 sensor hardware

(650 . . - . . . K - . . . .) only.

Note: For applications where the high range sensor is used for for monitoring

purpose only, select sensor operation modes 1 or 3 for pressure control with

low range sensor and read high range sensor from «SENSOR 2 READING»

resp. «SENSOR 1 READING».

1 = ZERO enabled, 0 = ZERO disabled

cdefgh

High range / Low range sensor full scale ratio * 1’000 (1000 … 100000).

In case of a 1 sensor valve use any value within the valid range.

This function does the sensor configuration for pressure control.

Содержание 650 GS Series














































































Результаты поиска

Содержание 650 GS Series

Отзывы:

Похожие инструкции для 650 GS Series

Бренды по названию

Популярные бренды

VAT 650 GS Series, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 650 GS Series

Отзывы:

Похожие инструкции для 650 GS Series

Бренды по названию

Популярные бренды