VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 8 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

8/77

2. Connect compressed air supply to connection labeled ‘IN’ located at actuator.

Connect compressed air return line connection labeled ‘OUT’ located at actuator.
Caution: Compressed air pressure must be in the range of: 4 - 7 bar / 55 - 100 psi (above ATM).
Note: Use only clean, dry or slightly oiled air. IN / OUT connections are 1/8“ ISO/NPT internal threads.

3. Install pressure sensor(s) [2] according to the recommendations of the sensor manufacturer and directives given

under
«Requirements to sensor connection».

4. Connect sensor cable [3] to sensor(s) and then to Master valve (connector: SENSOR).

Refer to chapter «Electrical connection» for correct wiring.

5. Connect Master valve to RS485 [4] (connector: INTERFACE). Refer to «RS485 schematics» for correct wiring.

6. Enable terminating resistor in link adapter of first and last valve in the system. Refer to «Valve cluster connection» for

details.

7. Connect link cable [6] between Slave valve(s) and Master valve (link adapter). Refer to «Valve cluster connection» for

correct wiring.

8. Connect power supply [5] to each valve (connector: POWER). Refer to chapter «Electrical connection» for correct

wiring.

Note: To provide power to the valve motor pins 4 and 8 must be bridged, otherwise motor interlock is active and the
valve enters the safety mode and is not operative. Refer also to «Safety mode».

9. These valves have a double sealed rotary feedthrough with intermediate pumping port for the actuator shaft. This port

(1/8“ ISO/NPT) may optionally be connected to the vacuum line.

10. These valves may optionally be equipped with a heating device. Connect VAT heating device according to manual of

respective heating device.

11. Perform «Setup procedure» to prepare valve cluster for operation.

Note: Without performing the setup procedure the valve cluster will not be able to do pressure control.

«
...
6
7
8
9
10
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: Eaton Страницы: 16

Бренд: Accel Страницы: 8

Бренд: GCE Страницы: 24

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

PowerFlex 755 IP00

Бренд: Allen-Bradley Страницы: 78

Бренд: Quantum Страницы: 20

Бренд: NXP Semiconductors Страницы: 39

Бренд: Dantherm Страницы: 28

Бренд: WANDERS Страницы: 16

SYNCHRO QUASAR AC

Бренд: UCS Страницы: 10

MultiMode 1214-8

Бренд: Curtis Страницы: 41

Бренд: Parker Страницы: 8

color LaserJet 5500

Бренд: IBM Страницы: 192

AUMATIC ACExC 01.2

Бренд: AUMA Страницы: 92

Бренд: KELD Страницы: 2

Бренд: Viessmann Страницы: 12

iAqualink IQ904-P

Бренд: Zodiac Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды