VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 22 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

22/77

3.1.5 Local

operation

Local operation means that the valve is operated via the service port using a computer or the Service Box 2. When using
a computer, a service cable and a software from VAT are required. You can either download our freeware 'Control View'
from

www.vatvalve.com

or purchase our 'Control Performance Analyzer'.

These software are beneficial especially for setup, testing and maintenance.

How to start: Connect service cable, start software and push button ‘LOCAL’ to enable for operation. Then enter menu
Setup/Sensor and do sensor configuration according to your application to make sure that you get the correct pressure
displayed.

‘Control view’ supports:

- parameter

setup

- manual

control

- numeric

monitoring

- basic

diagnostic

'Control Performance Analyzer'
supports:

- parameter

setup

- manual

control

- sequence

control

-

numeric and graphical
monitoring

- data

recording

- data

analysis

- advanced

diagnostic

When communication to service port is interrupted the valve will change to remote operation.
So when service cable will be disconnected or software will be shut down, the valve returns
automatically to remote operation.
This may result in an immediate movement of the valve depending on remote control.

Refer to «Spare parts / Accessories» for ordering numbers of service cable, software and Service Box 2.

3.1.6 Remote

operation

This product is equipped with a RS485 interface to allow for remote operation. See section «RS485 Interface» for details.
‘Control View’ software, 'Control Performance Analyzer' software or 'Service Box 2' may be used for monitoring during
remote control.
Note: In case ‘Control View’ or ‘Control Performance Analyzer’ software is connected to valve make sure ‘REMOTE’
button is pushed to enable for remote operation. In case Service Box 2 is connected to valve make sure the LED on
button ‘LOCAL’ is OFF for remote operation.

«
...
20
21
22
23
24
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: Jafar Страницы: 9

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 32

Бренд: HANYOUNG NUX Страницы: 56

Бренд: Mackie Страницы: 4

Бренд: Taco Electronic Solutions Страницы: 28

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 2

Бренд: WAC Страницы: 5

Бренд: Case IH Страницы: 81

Diaval AF Series

Бренд: Comeval Страницы: 10

SMARTCONNECT SMART/REP

Бренд: Zeta Alarm Systems Страницы: 48

Бренд: Eaton Страницы: 62

Бренд: Z-Wave Страницы: 27

Бренд: Bronpi Страницы: 65

Бренд: elsner elektronik Страницы: 148

Бренд: Zareba Страницы: 40

Бренд: fadini Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды