VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 26 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

26/77

3.6 Setup

procedure

To enable the valve cluster for pressure control setup steps 1 to 6 must be performed.
In case position control is required only it’s sufficient to perform steps 1 to 4.

Setup step

Description

Valve

1

Power up

Turn on ex 24VDC power supply for all valves
(and external

±

15 VDC for sensor power supply on

master valve if required). Refer to chapter «Behavior
during power up» for details.

Master & Slave

2

Cluster address

configuration

Set the cluster address for each individual valve
(Master and Slave(s)). This must be done via the
service port on each valve. Refer to chapter «Cluster
address configuration» for details

Master & Slave

3

Interface

configuration

RS485 parameters and digital inputs for valve may be
changed from the default values.
Refer to chapter «RS485 interface» for details.

Master

4

Valve and sensor

configuration

Basic configurations of the Master valve must be
adapted according to application needs. Refer to
chapter «Valve and sensor configuration» for details.

Master &
Slave (valve
configuration only)

5

ZERO

Compensation of the sensor offset voltage.
Refer to chapter «ZERO» for details.

Master

6

LEARN

Determination of the vacuum system characteristic to
accommodate the PID controller. Refer to chapter
«LEARN» for details.

Note: Without LEARN the valve is not able to run
pressure control

Master

3.6.1 Cluster

address

configuration

When setting up the valve cluster solution, each valve needs a unique cluster address.
This address must be configured on each valve prior to operation via the service port by using the graphical interface
(SETUP –> CLUSTER) or the Terminal function of the Control View software or Control Performance Analyzer software.
The used addresses must be in a consecutive order.
Further the Master valve needs the information about the total number of valves (including itself) connected to the valve
cluster.
Note: Prior to sending the address command, set the valve to LOCAL operation.

«
...
24
25
26
27
28
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: IBM Страницы: 144

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: DSE Страницы: 2

Бренд: Hattersley Страницы: 2

Бренд: National Instruments Страницы: 6

WisLink LPWAN RAK5146

Бренд: RAKwireless Страницы: 9

CURTIS DC Series

Бренд: NOCO Genius Страницы: 2

Бренд: TimeTec Security Страницы: 2

Бренд: Xylem Страницы: 2

Бренд: IR-Tec Страницы: 14

Бренд: bluelab Страницы: 39

Бренд: SOMFY Страницы: 2

Devicenet R7F4HD-DAC32C

Бренд: M-system Страницы: 9

Бренд: Universal Remote Страницы: 10

Бренд: Blue Point Engineering Страницы: 12

XBee DigiMesh 2.4

Бренд: Digi Страницы: 157

Бренд: Instrutech Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды