VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 31 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

31/77

3.6.3 Valve and sensor configuration

Basic valve configuration must be adapted according to application needs.

•

Definition of valve plate position (CLOSE or OPEN) after power up sequence. Default is ‘Close‘.

•

Definition of valve plate position (CLOSE or OPEN) in case of a power failure. Default is ‘Close‘.

•

Only for versions that have Power Fail Option equipped [650 . . - . . U . - . . . .; 650 . . - . . W . - . . . .].
Note: This definition must be set on Master and Slave valves.

•

ZERO function (Master only). This may be ‘disabled’ or ‘enabled’. Default is ‘enabled‘.
Refer also to «ZERO».

•

Sensor configuration for 2 sensor version [650 . . - . . . K - . . . .] (Master only).
Refer also to «Pressure control operation with 2 sensors».

Local operation

:

(‘Control View’, ‘Control Performance Analyzer’ or

‘Service Box 2‘)

Remote operation

:

(Refer to chapter «setup commands» for details)

1. Do power up configuration in menu

‘Setup / Valve’.

2. Do power fail configuration in menu

‘Setup / Valve’.

1. Send VALVE CONFIGURATION

3. Enable or disable ZERO function in menu

‘Setup / Sensor’.

4. Do sensor configuration in menu

‘Setup / Sensor’.

2. Send SENSOR CONFIGURATION

3.6.4 ZERO

This function is available on the Master valve only.
ZERO allows for the compensation of the sensor offset voltage.
When ZERO is performed the current value at the sensor input is equated to pressure zero. In case of a 2 sensor system
both sensor inputs will be adjusted. A max. offset voltage of +/- 1.4 V can be compensated. The offset value can be read
via local and remote operation.

Local operation

:

(‘Control View’, ‘Control Performance Analyzer’ or

‘Service Box 2‘)

Remote operation

:

(Refer to chapter «control commands» resp. «setup

commands» for details)

1. Send

OPEN

VALVE

2. Wait until process chamber is evacuated and

sensor signal is not shifting anymore.

Go to menu ‘Zero / ZERO’ and follow instructions.

3. Send

ZERO

Note: Do not perform ZERO as long as pressure gauge voltage is shifting otherwise incorrect pressure reading is the
result. Refer to manual of sensor manufacturer for warm up time.

Note: Do not perform ZERO, if the base pressure of your vacuum system is higher than 1‰ of sensor full scale. We
recommend disabling ZERO function in this case; refer to «Valve and sensor configuration» of the setup procedure.
Otherwise incorrect pressure reading is the result.

«
...
29
30
31
32
33
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: Gardena Страницы: 100

Бренд: IBM Страницы: 72

Бренд: Eaton Страницы: 6

Бренд: Eaton Страницы: 35

Бренд: Eaton Страницы: 18

Бренд: Eaton Страницы: 73

Бренд: Eaton Страницы: 4

Cutler-Hammer IQ DP-4000

Бренд: Eaton Страницы: 87

Бренд: Eaton Страницы: 14

Бренд: Eaton Страницы: 36

Бренд: Federal Signal Corporation Страницы: 34

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: NAPCO Страницы: 48

Magnum Alert 2600

Бренд: NAPCO Страницы: 68

CEmarking RCX221

Бренд: Yamaha Страницы: 468

Бренд: TCi Страницы: 9

Бренд: Zaiput Flow Technologies Страницы: 10

Бренд: Hunter Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды