VAT 650 GS Series Скачать руководство пользователя

Страница: 51 / 77

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

51/77

3.11.9 Setup commands

Command

Acknowledgement

(within 10ms after reception of command)

Setup function

Description

Set [c:01][xx][CR][LF]

[c:01][CR][LF]

ACCESS MODE

data length: 2 characters

00 = local operation (service port)

01 = remote operation, change to local enabled

02 = locked remote operation, change to local not possible via service port

This function selects the access authorization to the valve. To read access mode use
inquiry command DEVICE STATUS.

Note: Local operation is only possible when either ‘Control View’ or ‘Control Performance
Analyzer’ software is running. When communication to service port is interrupted the valve
will automatically change to remote operation.

Set [s:20][abcdefgh][CR][LF]

[s:20][CR][LF]

Get [i:20][CR][LF]

[i:20][abcdefgh][CR][LF]

INTERFACE

CONFIGURATION 1

data length 8 characters
a

baud rate:

0 = 600, 1 = 1200k, 2 = 2400, 3 = 4800, 4 = 9600

5 = 19.2k, 6 = 38.4k, 7 = 57.6k, 8 = 115.2k

parity bit: 0 = even, 1 = odd, 2 = mark, 3 = space, 4 = no

data length: 0 = 7 bit, 1 = 8 bit

number of stop bits: 0 = 1, 1 = 2

0 (reserved, do not change)

digital input OPEN VALVE:

0 = not inverted, 1 = inverted, 2 = disabled

digital input CLOSE VALVE: 0 = not inverted, 1 = inverted, 2 = disabled

0 (reserved, do not change)

This function does the RS485 and digital input configuration.

Note: Digital outputs are always enabled.

Set [s:22][abbbcxxx][CR][LF] [s:22][CR][LF]

Get [i:22][CR][LF]

[i:22][abbbcxxx][CR][LF]

INTERFACE

CONFIGURATION 2

data length 8 characters

1 = RS485, 2 = RS485 / Point to Point

bbb RS485

address

0...999

0 = full duplex, 1 = half duplex

xxx

000 (reserved, do not change)

This function defines the interface configuration for the valve.

Содержание 650 GS Series














































































Результаты поиска

Содержание 650 GS Series

Отзывы:

Похожие инструкции для 650 GS Series

Бренды по названию

Популярные бренды

VAT 650 GS Series, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 650 GS Series

Отзывы:

Похожие инструкции для 650 GS Series

Бренды по названию

Популярные бренды