VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 21 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

21/77

3.1.1 Individual

valve

control

This function is available on the Master valve only.
It is possible to individually control any valve in the valve cluster.
When commanding an individual valve to a certain position, make sure the target valve is set to ‘Freeze mode’ previously
(refer to chapter «3.1.3 Freeze mode»), so it will listen to individually addressed commands and execute them. Once set
to Freeze Mode the valve will execute any command addressed directly to it, until it is released from Freeze Mode. Refer
to chapter «Control commands» > «INDIVIDUAL VALVE CONTROL» for details.

3.1.2 Individual

valve

status

This function is available on the Master valve only.
The Master valve holds a record of information about the status of the complete valve cluster. Therefore status information
about all valves (Master and Slave(s)) connected to the valve cluster is available from the Master valve. Refer to chapter
«Inquiry commands» > «CLUSTER VALVE STATUS» for details.

3.1.3 Freeze

mode

This mode enables an individual valve to be controlled independent of the valve cluster. As soon as a valve is set to
Freeze mode (freeze), it will remain in the last position it received from the Master valve before it was frozen. Now it is
listening to commands addressed directly to it. Refer to chapter «Setup commands» > «FREEZE MODE» and «Inquiry
commands» > «FREEZE MODE» for details.

Note: The Freeze mode status is stored in a power save memory of each individual valve. In case valve was in freeze

mode before power cycle (power off, power on), valve will stay in freeze mode after power up.

Attention: As soon as a valve is unfrozen, the valve starts to follow the Master valves plate

position, meaning the plate might move immediately.

3.1.4 Position

offset

The position offset can be used to add or subtract a certain offset value from the current position that is received from the
Master valve. It might be helpful to compensate variations in pumping speed of the individual exhaust lines. Refer to
chapter «Setup commands» > «CLUSTER POSITION OFFSET» for details.

Note: The position offset value will be stored in a power save memory of each individual valve.

«
...
19
20
21
22
23
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: Danfoss Страницы: 24

Бренд: Kathrein Страницы: 16

Бренд: RADEMACHER Страницы: 48

Бренд: Vaillant Страницы: 11

Бренд: Fingertips Lab Страницы: 15

Бренд: D&R ELECTRONICS Страницы: 12

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

Бренд: Tech 21 Страницы: 2

Бренд: Dejero Страницы: 24

Бренд: WINDY NATION Страницы: 16

Бренд: Kaba Mauer Страницы: 10

Micro850 series

Бренд: Allen-Bradley Страницы: 24

Бренд: Fluidmaster Страницы: 2

Бренд: Penn Страницы: 10

Бренд: Gecko Страницы: 82

Бренд: Motorline professional Страницы: 8

Бренд: Swagelok Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды