VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 42 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

42/77

3.11.4 Digital inputs

Pin

Function

Signal type Description

Priority

15

CLOSE VALVE

Digital

input

1)

This function will close the valve.
Valve will be in interlock mode as long as function is activated.
After deactivation of function it will remain effective until
- OPEN valve digital input is active
- converse RS485 control command have been received

The function is activated when optocoupler is ‘on’ in non
inverted configuration.

The function is activated when optocoupler is ‘off’ in inverted
configuration.

Configuration can be done in local operation via service port or
in remote operation.

1

2)

17

OPEN VALVE

Digital

input

1)

This function will open the valve.
Valve will be in interlock mode as long as function is activated.
After deactivation of function it will remain effective until
converse RS485 control command have been received.

The function is activated when optocoupler is ‘on’ in non
inverted configuration.

The function is activated when optocoupler is ‘off’ in inverted
configuration.

Configuration can be done in local operation via service port or
in remote operation.

2

2)

23

DIGITAL GROUND

Digital

ground

Ground for all digital inputs. Ground is used when digital inputs
are operated by switches. Connect switches to ground.
See also «3.11.2 Schematics» configuration a).

25

DIGITAL COMMON

Digital

common

Common for all digital inputs. Common is used when digital
inputs are driven by voltage sources. C or – terminal of
source with common (optocoupler inputs are capable of
bidirectional operation).
See also «3.11.2 Schematics» configuration b).

1) All digital inputs are digitally filtered. Filter delay is 50ms. This means that digital signals must be applied for

at least 50ms to be effective.
Refer to «3.11.2 Schematics» for details about input circuit.

2) Highest priority is 1. Functions with lower priorities will not be effective as long as higher priority functions

are active. These digital inputs have higher priority than all RS485 commands. RS485 commands will not be
accepted while digital inputs are active.

«
...
40
41
42
43
44
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: Dahua Страницы: 58

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

Slim Remote Control

Бренд: Packard Bell Страницы: 2

Бренд: Unipower Страницы: 24

Бренд: GEA Страницы: 13

Бренд: Black Horse Model Страницы: 19

Бренд: Apex Toys Страницы: 7

Бренд: Forcepoint Страницы: 15

VPPM-...-LK Series

Бренд: Festo Страницы: 4

Бренд: SMC Networks Страницы: 12

M-DUINO PLUS series

Бренд: Industrial Shields Страницы: 46

Бренд: Harman Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Nortek Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды