VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 20 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

20/77

3 Operation

Operation is allowed after completion of the installation procedure only.

3.1 Introduction

The valve cluster solution is designed to operate multiple valves (exhaust lines) installed on a single process chamber in
parallel. The system consists of one Master valve and a number of Slave valves. A valve cluster can have up to 255
valves. Each valve in the Cluster has a unique cluster address (see chapter «Cluster address configuration (setup step
2)» for details). A digital field bus system is used for the inter communication between the Master and the Slave valves.
The Master valve is taking care of the pressure control, while the Slave valves are following the Master valves plate
position. It can be operated in pressure control mode or in position control mode. In both cases local or remote operation
is possible.
Therefore the host system mainly communicates with the Master valve. The Master valve then takes care of controlling the
Slave valves. All status information about the condition of each individual valve in the Cluster can be requested from the
Master valve.
For basic operation of the valve cluster the known standard command set is used. In addition there are special commands
available for getting status information of each valve connected to the Cluster. Further it is possible to control individual
Slave valves independently. For example, it is possible to close a single valve, while the valve cluster is still operational.
There is also a parameter (Position offset) for fine tuning single exhaust lines.

120

Ω

terminator

category 5 cables

120

Ω

terminator

valve cluster daisy chain

«
...
18
19
20
21
22
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: Samson Страницы: 48

Бренд: Mako Networks Страницы: 15

Бренд: Daikin Страницы: 5

Бренд: Häfele Страницы: 2

Бренд: Häfele Страницы: 24

Бренд: Harman Страницы: 2

Бренд: T-Link Страницы: 3

Бренд: Jabra Страницы: 18

Бренд: Lamtec Страницы: 136

Бренд: Tylo Страницы: 51

infi 90 IMMFP12

Бренд: Bailey Страницы: 75

iSteam 2.0 Control

Бренд: mr. steam Страницы: 16

Бренд: Sygonix Страницы: 12

Бренд: Atari Страницы: 3

Бренд: Konig Страницы: 47

Бренд: Wilo Страницы: 128

Бренд: Phoenix Contact Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды