VAT 650 GS Series Скачать руководство пользователя

Страница: 57 / 77

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

57/77

3.11.10 Error messages

Description

Error message

Protocol

Parity error

[E:][000001][CR][LF]

Framing error (data length, number of stop bits)

[E:][000003][CR][LF]

Input buffer overflow (to many characters)

[E:][000002][CR][LF]

Commands

<CR> or <LF> missing

[E:][000010][CR][LF]

: missing

[E:][000011][CR][LF]

Unknown command

[E:][000020][CR][LF]
[E:][000021][CR][LF]

Invalid value

[E:][000022][CR][LF]
[E:][000023][CR][LF]

Value out of range

[E:][000030][CR][LF]

Invalid number of characters (between : and [CR][LF])

[E:][000012][CR][LF]

Setup

ZERO disabled

[E:][000060][CR][LF]

Device Status

Command not accepted due to local operation

[E:][000080][CR][LF]

Command not accepted due to synchronization, CLOSED or OPEN by digital input,
safety mode or fatal error

[E:][000082][CR][LF]

Hardware

Command not applicable for hardware configuration

[E:][000041][CR][LF]

Valve Cluster

Checksum failure (communication failure on cluster bus system)

[E:][000005][CR][LF]

Timeout expired (slave offline, no feedback from slave)

[E:][000006][CR][LF]

Control command rejected (slave valve not frozen)

[E:][000083][CR][LF]

Illegal slave command (e.g. sensor setup command)

[E:][000084][CR][LF]

Address out of range (slave address not in configured range)

[E:][000085][CR][LF]

Command not implemented on master valve (slave valve command only)

[E:][000086][CR][LF]

Command not implemented on slave valve (master valve command only)

[E:][000087][CR][LF]

Address information missing (G:xx prefix missing)

[E:][000088][CR][LF]

Содержание 650 GS Series














































































Результаты поиска

Содержание 650 GS Series

Отзывы:

Похожие инструкции для 650 GS Series

Бренды по названию

Популярные бренды

VAT 650 GS Series, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 650 GS Series

Отзывы:

Похожие инструкции для 650 GS Series

Бренды по названию

Популярные бренды