VAT 650 GS Series Скачать руководство пользователя | Manualshive

Страница: 12 / 77

background image

Installation, Operating & Maintenance Instructions

Series 650 DN 100-250 (I.D. 4“ - 10”), RS485

VAT Vakuumventile AG, CH-9469 Haag, Switzerland

Tel ++41 81 771 61 61 Fax ++41 81 771 48 30 Email

[email protected]

www.vatvalve.com

271149EA

2007-06-12

12/77

2.6 Electrical

connection

2.6.1 Sensor supply concepts

This valve offers 3 alternative concepts to supply the sensor(s) with power. This depends on the sensor type and valve
version that is used. This valve is available with an optional sensor power supply module (SPS) that converts

±

15 VDC

from the 24 VDC.

Concepts:

•

Ex 24 VDC supplied to POWER connector is feed through to SENSOR connector to supply 24 VDC
sensors. Refer to chapter «2.6.2 Power and sensor connection (+24 VDC sensors)» for schematic and correct
wiring.

•

External

±

15 VDC supplied to POWER connector is feed through to SENSOR connector to supply

±

15 VDC

sensors. Refer to chapter «2.6.3 Power and sensor connection (

±

15 VDC sensors) without optional SPS module»

for schematic and correct wiring.

•

Ex 24 VDC supplied to POWER connector is converted into

±

15 VDC by the valve internal SPS and

supplied to SENSOR connector to supply

±

15 VDC sensors. Refer to chapter «2.6.4 Power and sensor

connection (

±

15 VDC sensors) with optional SPS module» for schematic and correct wiring.

Valve versions:

•

650 . . - . . T . - . . . . / 650 . . - . . U . - . . . .

SPS module not included

•

650 . . - . . V . - . . . . / 650 . . - . . W . - . . . .

SPS module included

•

650 . . - . . . S - . . . .

slave valve, no sensor connection

Note: The SPS module can be retrofitted. Refer to chapter «Retrofit / replacement procedure» for instruction.

«
...
10
11
12
13
14
...
»

Содержание 650 GS Series














































































Отзывы:

Нет отзывов

Похожие инструкции для 650 GS Series

Бренд: Nelsen Corporation Страницы: 16

Бренд: National Instruments Страницы: 34

Бренд: Quickmill Страницы: 3

Бренд: rada Страницы: 16

Бренд: VAT Страницы: 27

Бренд: ICP DAS USA Страницы: 148

Бренд: ICMA Страницы: 8

Бренд: MacDon Страницы: 32

Бренд: K&K Страницы: 6

Бренд: National Instruments Страницы: 8

Бренд: National Instruments Страницы: 2

Бренд: Keba Страницы: 16

Бренд: KEB Страницы: 16

Бренд: YOKOGAWA Страницы: 150

Бренд: YOODA Страницы: 3

Бренд: YMGI Страницы: 8

Бренд: Sabiana Страницы: 60

Бренд: Danfoss Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды