KAPITEL 3 - BETRIEBANWEISUNG
95
87-900-045-01
(D)
Ist die wirkliche Heliumkonzentration niedriger als der
Nullpunkt, reagiert die Anzeige mit einigen "<"-Zeichen.
Jedes dieser Zeichen entspricht ca. 2 ppm unter dem
Nullpunkt. Außerdem blinkt die "0" Anzeige.
Mit der Funktion "automatischer Nullabgleich" kann das
Gerät auf Null gebracht werden.
Ist kein Helium vorhanden, schalten Sie das Gerät auf
automatischen Nullabgleich und warten bis die Anzeige
keine "<" Zeichen mehr zeigt und die Nullanzeige nicht
mehr blinkt. Das Gerät ist jetzt in der Lage weniger als
1 ppm. Konzentrationsänderung zu messen und man
kann jetzt bei festem Nullpunkt arbeiten indem man
wiederum die "ZERO"-Taste drückt.
3.3.6 Schwellwert-Modus
Durch Drücken der "MODE" Taste kann dieser Modus
aktiviert bzw. deaktiviert werden. Nachdem die "MODE"
Taste zum ersten Mal gedrückt wurde, ist der
Schwellwert aktiviert und der eingestellte Schwellwert
erscheint im Display (Abbildung 3-31).
I . . . . . . . . . I 0
S
P Y
Y
Y Y *
Abbildung 3-31
Danach wird die eingestellte Maßeinheit angezeigt
(Abbildung 3-32).
I . . . . . . . . . I 0
S P X X X X X X X *
Abbildung 3-32
Wenn ein Leck, welches geringer als der Schwellwert
ist, gemessen wird, wird der Wert regulär angezeigt.
Wenn der Schwellwert überschritten wird, wird der
Wert ständig angezeigt und auf der Anzeige erscheint
"LEAK" (siehe Abbildung 3-33).
❙❙❙❙
. . . . . . . . .
❙❙❙❙
L E A K
S P X X X X X X X *
Abbildung 3-33
Wenn der Wert des Leckes unter den Schwellwert
geht, wird das aktuelle Leck wieder angezeigt und das
"LEAK" Signal verschwindet.
ANMERKUNG
Solange der Schwellwert aktiviert ist, ist der
proportional zum Heliumsignal unterbrochene Piepton
abgestellt und das Dauersignal (welches das über dem
Schwellwert liegende Leck anzeigt) ist aktiviert.
3.3.7 Funktion "CLEANUP"
ANMERKUNG
Bevor Sie das Gerät mit dieser Funktion regenerieren,
bringen Sie es heraus aus jeglicher Beeinflussung
durch Helium.
Wenn die Sonde hohen Heliumkonzentrationen (über
10
4
ppm) ausgesetzt wurde und die Konzentration im
Instrument auch nach der Entfernung von der
Heliumquelle hoch bleibt, besteht die Möglichkeit, das
Instrument mittels der Funktion "CLEANUP" zu
"reinigen".
Durch gleichzeitiges Drücken der "ZERO" und der
"PROBE"-Taste für etwa 2 Sek., kann ein schneller
Nullabgleich nach einer Sättigung mit Helium erreicht
werden. In der Anzeige erscheint Abbildung 3-34.
- - C L E A N U P - -
❙❙❙❙
. . . . . . . . . . .
❙❙❙❙
*
Abbildung 3-34
Ist der Regenerierungsprozess abgeschlossen
(minimum 30 Sek.), erscheint in der Anzeige Abbildung
3-35.
- - C L E A N U P - -
O K
*
Abbildung 3-35
danach geht HeliTest automatisch zurück in den
Betriebszustand, in dem vorher gearbeitet wurde.
Wenn 5 Min. nachdem die Funktion
"REGENERIEREN" eingeleitet wurde, der Nullpunkt
nicht erreicht wurde, erscheint die Anzeige Abbildung
3-36.
- - C L E A N U P - -
N I C H T
K O M P L E T T *
Abbildung 3-36
ANMERKUNG
Wenn diese Anzeige erscheint, wird HeliTest nach 1
Min. automatisch abgeschaltet.
Wiederholen Sie den automatisch abgelaufenen
Eigentest (Paragraph 3.2.1), wenn die
"REGENERIERUNG" nicht erfolgreich beendet wurde.