KAPITEL 3 - BETRIEBANWEISUNG
93
87-900-045-01
(D)
Danach wird die Schnüffelleitung und Schnüffelpumpe
getestet, in der Anzeige erscheint Abbildung 3-18.
S o n d e
*
Abbildung 3-18
Ist nach etwa 10 Sek. dieser Test erfolgreich
abgeschlossen worden, erscheint Abbildung 3-19 auf
der Anzeige.
S o n d e
O K
*
Abbildung 3-19
In der Anzeige erscheint Abbildung 3-20 wenn
Schnüffelleitung und oder Schnüffelpumpe defekt sind.
S o n d e
D
E
F
E K
T *
Abbildung 3-20
ANMERKUNG
Diese Anzeige bleibt für etwa 1 Min. bestehen. Dann
wird HeliTest automatisch abgeschaltet. In diesem
Falle tun Sie bitte folgendes:
- Prüfen Sie, ob der Filter an der Schnüffelsonde
oder an der Teleskopschnüffelsonde verstopft ist
und reinigen Sie ihn (Einzelheiten finden Sie in
Sektion IV, Wartung und Ersatzteile).
- Wiederholen Sie den Eigentest gemäß
Paragraph 3.2.
Sollte der Eigentest wiederum Defekt anzeigen, rufen
Sie bitte das nächste Büro an.
Wird der Eigentest erfolgreich abgeschlossen, etw 10
Sek. nach dem letzten Schritt, erscheint Abbildung 3-
21 in der Anzeige.
E i g
e
n t e
s t
K
O
M
P
L E
T
T *
Abbildung 3-21
3.3 MEßBETRIEB
Etwa 10 Sek. nach dem Eigentest erscheint Abbildung
3-22 in der Anzeige.
B E T R I E B S B E R E I T
H S
M S
P . O N
A Z
*
Abbildung 3-22
Das HeliTest Gerät ist nun betriebsbereit mit den
folgenden werkseitig getroffenen Einstellungen:
HS = Hohe
Empfindlichkeit
MS = Meßbetrieb
P.ON =
Schnüffelsonde in Betrieb
AZ = Automatischer
Nullabgleich
Wenn die Schnüffelsonde nicht innerhalb 1 Min. dem
Gehäuse entnommen wurde, geht HeliTest in die
Warteposition, um Energie zu sparen und zeigt
Abbildung 3-23.
In der Warteposition wird HeliTest automatisch nach 45
Min. abgeschaltet, wenn er nicht vorher in Betrieb
genommen worden ist.
B E T R I E B S B E R E I T
H S
M S
P . O N
A Z
*
Abbildung 3-23
In beiden Situationen (Abbildung 3-22 oder Abbildung
3-23), wenn die Schnüffelsonde dem Gehäuse
entnommen worden ist, erscheint in der Anzeige
Abbildung 3-24 (für etwa 5 bis 50 Sek.)
- > B E T R I E B S B E R E I T
B I T T E
W A R T E N
*
Abbildung 3-24
Ein weiterer Test wird an der Schnüffelleitung, der
Schnüffelpumpe und am Heizfaden durchgeführt. In
der Anzeige erscheint Abbildung 3-25.
❙❙❙❙
. . . . . . . . .
❙❙❙❙
0
p p m
*
Abbildung 3-25
und der HeliTest ist jetzt meßbereit. In der Anzeige
können Konzentrationen zwischen 0 ppm und
9 x 10
5
ppm erfaßt werden. Dabei entspricht die Anzahl
der gezeigten Balken der Mantisse dieses Meßwertes.
Bei negativen Werten (betrifft nur elektrische
Schwankungen der Anzeige) kann die "0" blinken und
es werden "<" Zeichen erscheinen (siehe Paragraph
3.3.5).