Varian 948 страница 6 Скачать руководство пользователя

Страница: 6 / 176

Models 947, 948 and 960 Leak Detectors Operations and Service Manual

B.1.2 Removing the Top Panel ...........................................................................................B-3
B.1.3 Replacing all Panels and Covers ...............................................................................B-4

B.1.3.1 Replacing the Service Pendant Shelf .............................................................B-4
B.1.3.2 Replacing the Top Panel ................................................................................B-5

B.2 Replacing the Ion Source ....................................................................................................B-6
B.3 Replacing the Turbo Pump..................................................................................................B-9

B.3.1 Turbo Pump ...............................................................................................................B-9

B.3.1.1 Removing the Turbo Pump...........................................................................B-10
B.3.1.2 Replacing the Turbo Pump ...........................................................................B-12

B.3.1.2.1 Examining and Cleaning Centering Rings, O-rings and Manifold.B-12
B.3.1.2.2 Connecting the Turbo Pump to the SVBA ....................................B-13

B.4 Replacing the Rough Pump...............................................................................................B-15

B.4.1 Wet Systems ...........................................................................................................B-15

B.4.1.1 Removing the Wet System Rough Pump .....................................................B-16

B.4.1.1.1 Replacing the Wet System Rough Pump.......................................B-17
B.4.1.1.2 Examining and Cleaning Centering Rings, O-rings and Manifold .B-17
B.4.1.1.3 Re-installing the Wet System Rough Pump ..................................B-18

B.4.2 Dry Systems ............................................................................................................B-20

B.4.2.1 Removing the Dry System Rough Pump ......................................................B-20
B.4.2.2 Replacing the Dry System Rough Pump ......................................................B-21

B.4.2.2.1 Examining and Cleaning Centering Rings, O-rings and Manifold..B-21
B.4.2.2.2 Re-installing the Dry System Rough Pump ...................................B-21

B.5 Replacing the Forepump ...................................................................................................B-22

B.5.1 Wet ..........................................................................................................................B-22

B.5.1.1 Removing the Wet System Forepump..........................................................B-23
B.5.1.2 Replacing the Wet System Forepump ..........................................................B-24

B.5.1.2.1 Examining and Cleaning Centering Rings, O-rings and Manifold..B-24
B.5.1.2.2 Re-installing the Wet System Forepump ......................................B-24

B.5.2 Dry System ..............................................................................................................B-26

B.5.2.1 Removing the Dry System Forepump...........................................................B-26

B.5.2.1.1 Removing the Isolation Valve from the Forepump.........................B-26
B.5.2.1.2 Removing the Nitrogen Purge Connection from Pump .................B-27
B.5.2.1.3 Removing the Exhaust Fitting .......................................................B-27
B.5.2.1.4 Removing the Pump from the Cabinet ..........................................B-27

B.5.2.2 Replacing the Dry System Forepump...........................................................B-27

B.5.2.2.1 Examining and Cleaning Centering Rings, O-rings and Manifold..B-27
B.5.2.2.2 Re-installing the Dry System Forepump  .......................................B-28
B.5.2.2.3 Connecting the Nitrogen Purge Pump  ..........................................B-28
B.5.2.2.4 Replacing the Isolation Valve ........................................................B-28
B.5.2.2.5 Replacing the Exhaust Fitting  .......................................................B-29
B.5.2.2.6 Completing Mounting the Pump to the Cabinet Floor  ...................B-29

Содержание 948

















































































































































































Результаты поиска

Содержание 948

Отзывы:

Похожие инструкции для 948

Бренды по названию

Популярные бренды

Varian 948, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 948

Отзывы:

Похожие инструкции для 948

Бренды по названию

Популярные бренды