manualshive.com logo in svg

Varian 948, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Varian 948 Скачать руководство пользователя страница 50

Models 947, 948 and 960 Leak Detectors Operations and Service Manual 

3-2

During operation, the LED functions are illuminated to indicate the operation being 
performed. The definitions of the operations are as follows:

VENT

Illuminates when the vent valve is open. The LED is off when the 
valve is closed.

START

Illuminates when the START button is pushed. Goes off one 
second after the TEST LED illuminates, or immediately when the 
VENT, HOLD, or NOT READY LEDs illuminate.

TEST

Illuminates when 947/948/960 is in test mode; either the gross leak 
valve or the test valve is open. Otherwise, the LED is off.

ZERO

Illuminates when the ZERO button is pushed or when the auto-zero 
sequence is performed as part of the auto-calibrate sequence. Goes 
off one second after the auto-zero sequence is completed or if the 
leak detector goes into a not-ready condition. The ZERO LED 
flashes when the signal falls below zero. The ZERO LED also 
flashes during startup when the system is nulling the preamplifier.

REJECT

Illuminates when the reject function is on and when the leak rate 
reading exceeds the selected set point. Goes off when the leak rate 
falls below the set point. 

HOLD

Illuminates if the machine is in the HOLD mode with the test and 
roughing valves closed. The HOLD mode is selected by momen-
tarily pressing the VENT button if the machine is in TEST. When in 
HOLD, pressing either the START or VENT button launches the 
next operation.

NOT READY

Illuminates whenever a not-ready condition exists. The particular 
error condition code, c0 through c9, is displayed on the RANGE 
DISPLAY. See Table 3-1 on page 3-11 for information on the error 
codes.

AUTO CAL

If the leak detector is in TEST mode, illuminates when the AUTO 
CAL button is pushed, disabling all other front panel push buttons, 
including START and VENT. AUTO CAL is only functional when 
the leak detector is in TEST mode. The machine returns to TEST 
mode at completion of the AUTO CAL routine. 

STD LEAK

Illuminates when the standard leak test valve is opened. This 
occurs when the STD LEAK button is pushed or during the auto-cal-
ibrate function. Goes off when the standard leak test valve is closed 
by pressing the STD LEAK button.

SERVICE

Not used.

Содержание 948

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды