Varian 948 страница 96 Скачать руководство пользователя

Страница: 96 / 176

Models 947, 948 and 960 Leak Detectors Operations and Service Manual

4-30

9. Type XYZZY<CR>, then 100 INIT-TPTCZERO<CR>.

❑

The system should respond

❑

The test port pressure on the test port pressure bar graph should read 1.0E-01 Torr.

FAILED

response on the PC is an indication that the calibration was not successful.

This could be the result of a defective or contaminated thermocouple gauge. If
necessary, replace the thermocouple gauge.

If after replacing the thermocouple gauge, calibration is still not successful, contact
Varian Vacuum Technologies Customer Service at 1-800-8VARIAN.

10. If the calibration was successful:

❑

Press the

VENT

button and remove the T-manifold, tuning leak, and reference TC

from the test port.

❑

Place test port plug into the test port and tighten the test port tightening nut fully.

❑

Remove the PC and connect the Service Pendant.

❑

Perform the next part of the calibration procedure (“Atmospheric Calibration”).

4.2.7.7 Atmospheric Calibration

To perform atmospheric calibration:

1. If the system is not already in VENT mode, press the

VENT

button and verify that the

VENT LED is illuminated.

2. Wait approximately ten seconds for the test port pressure to stabilize.

3. On the Service Pendant, press the

TP TC ATM

key.

❑

The Pendant screen confirms that the calibration was successful by displaying the

prompt.

❑

The Pendant screen displays

FAILED

before the

prompt, indicating that the

calibration was not successful. This could be the result of a defective or
contaminated thermocouple gauge, or that the actual pressure was not at or near
atmosphere

If the calibration was:

❑

Not successful, contact Varian Vacuum Technologies Customer Service at
1-800-8VARIAN.

❑

Successful, calibration of the TC1 gauge is complete. You can now proceed with test-
ing or place the system in the mode you desire.

Содержание 948

















































































































































































Результаты поиска

Содержание 948

Отзывы:

Похожие инструкции для 948

Бренды по названию

Популярные бренды

Varian 948, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 948

Отзывы:

Похожие инструкции для 948

Бренды по названию

Популярные бренды