Varian 948 страница 136 Скачать руководство пользователя

Страница: 136 / 176

Models 947, 948 and 960 Leak Detectors Operations and Service Manual

B-22

12. Replace the front panel.

13. Replace the side panel.

14. Reconnect the mains power supply.

15. Turn the leak detector on and wait for the system to be ready.

Allow the pumps to warm up if the detector has been off for some time.

NOTE

Allow a new pump to run for one hour and then perform an
autocal.

16.

Models 948/960 only:

Once the system has pumped down, clean and fill the Liquid

Nitrogen Cold Trap using the procedure described in “Liquid Nitrogen Cold Trap
(Models 948/960 only)” on page 4-10.

Follow all warnings and cautions in the procedure.

17. Calibrate the 947/948/960 using the procedure described in “Re-calibrate the Internal

Calibrated Leak” on page 4-7.

18. Leak check the assembly before using the 947/948/960 for testing.

B.5 Replacing the Forepump

B.5.1 Wet

This section includes procedures for replacing forepumps in wet systems (“Removing the
Wet System Forepump” on page B-23) and forepumps in dry systems (“Removing the Dry
System Rough Pump” on page B-20).

In both cases, the forepump is mounted on the bottom of the right side of the main cabinet.

WARNING

To avoid injury, use proper lifting techniques when moving
pumps. Your system may have pumps that require two people
to move them safely.

Before replacing the forepump:

❑

Refer to the appropriate pump operations manual.

❑

Ensure that the replacement pump is either the same one as you are replacing, or a
pump that can be used in its place.

Содержание 948

















































































































































































Результаты поиска

Содержание 948

Отзывы:

Похожие инструкции для 948

Бренды по названию

Популярные бренды

Varian 948, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 948

Отзывы:

Похожие инструкции для 948

Бренды по названию

Популярные бренды