Varian 948 страница 27 Скачать руководство пользователя | Manualshive

Страница: 27 / 176

background image

Models 947, 948 and 960 Leak Detectors Operations and Service Manual

1-5

5. Remove any loose boxes or packages and put them aside. Keep

the original packing for

re-use in the event that it is necessary to return the leak detector to Varian Vacuum
Technologies.

6. Carefully remove the front brace by removing the two lag bolts.

7. Carefully remove the plastic bag covering the leak detector.

The leak detector can now be removed from the skid.

1.2.2 Removing the 947/948/960 from the Skid

There are two methods for removing the 947/948/960 from the skid. Both methods
require two people. The second method involves removing the Skid-Mates from the
skid.

WARNING

Handle the leak detector carefully and properly in the following
steps. Personal injury or damage to the leak detector could
result from improper handling. The 947/948/960 is heavy and
can cause personal injury if not handled carefully when
removing it from the skid.

Method 1

1. With the assistance of a helper, carefully roll the leak detector toward the front of the

skid.

2. Lift the front end of the unit and

gently

lower it onto the floor.

3. Lift the rear of the unit and roll it on the front casters until it is clear of the skid.

4.

Gently

lower the rear end onto the floor.

Method 2

1. Using the brace removed in step 6 of “Unpacking Instructions” as a lever, carefully raise

the front edge of the skid between 1" and 2".

2. While a helper holds the leak detector against the back brace, unscrew and remove the

front two

Skid-Mates

(the blue donut-shaped mounts at the front of the skid) by turning

them in a counterclockwise direction.

3. Make sure the helper is still holding the leak detector against the back of the skid, then

gently lower the front of the skid to the floor.

4. Carefully and slowly roll the leak detector off the skid and onto the floor.

«
...
25
26
27
28
29
...
»

Содержание 948

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 948

GO!control 2GIG-CNTRL2

Бренд: 2gig Technologies Страницы: 52

GO!control 2GIG-CNTRL2

Бренд: 2gig Technologies Страницы: 52

Бренд: La Crosse Technology Страницы: 2

Бренд: Sanlien Страницы: 42

Бренд: Wavetronix Страницы: 4

Бренд: wavestore Страницы: 11

Бренд: X-10 Страницы: 32

Бренд: Panasonic Страницы: 228

Бренд: 2N Telekomunikace Страницы: 12

IQ PANEL 2 PLUS

Бренд: QOLSYS Страницы: 2

Бренд: e-Line Technology Страницы: 2

Бренд: jablotron Страницы: 2

Бренд: ChinaPST Страницы: 2

Бренд: EverFocus Страницы: 26

Бренд: Viking Страницы: 2

Бренд: Blaupunkt Страницы: 61

Бренд: SecurityMan Страницы: 2

Delta+ 90 FreshAir

Бренд: Kemppi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды