manualshive.com logo in svg

Varian 948, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Varian 948 Скачать руководство пользователя страница 7

Models 947, 948 and 960 Leak Detectors Operations and Service Manual 

vii

Appendix C. Communications Protocol  ......................................................................................... C-1

C.1 Protocol (RS-232)............................................................................................................... C-1

Appendix D. Inputs and Outputs  .................................................................................................... D-1

D.1 Service Serial Interface (J1) ............................................................................................... D-1
D.2 Optional Rear Panel Interface ............................................................................................ D-1

D.2.1 Discrete I/O Parallel Interface (J120)  ....................................................................... D-1
D.2.2 BCD Discrete Output Parallel Interface (J121)  ......................................................... D-3
D.2.3 Interface (J122) for Optional Universal Remote Control ........................................... D-4
D.2.4 Host Serial Port (J123)  ............................................................................................. D-4

Appendix E. 947/948 Specifications  ...............................................................................................E-1

Appendix F. Accessories  ................................................................................................................ F-1

Appendix G. Leak Detection Theory  .............................................................................................. G-1

G.1 Leak Testing—Why is it Needed? ...................................................................................... G-1
G.2 Classes of Leak Detection ................................................................................................. G-1
G.3 Terminology ....................................................................................................................... G-2
G.4 Various Methods of Testing for Leaks................................................................................ G-3
G.5 Helium Mass Spectrometer Leak Detection (MSLD) ......................................................... G-4

G.5.1 Principles of Mass Spectrometry .............................................................................. G-4
G.5.2 Application as a Leak Detector ................................................................................. G-4
G.5.3 The Nature of Flow in a Vacuum .............................................................................. G-4
G.5.4 Facts About Leak Rates  ........................................................................................... G-5

G.6 Leak Detection Methods .................................................................................................... G-5

G.6.1 Test Piece Evacuated  .............................................................................................. G-6
G.6.2 Test Piece Pressurized  ............................................................................................ G-6
G.6.3 Test Piece Already Sealed  ....................................................................................... G-7

G.7 Mass Spectrometer Leak Detector—Simplified Description .............................................. G-8

Содержание 948

















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды