Varian 948 страница 67 Скачать руководство пользователя | Manualshive

Страница: 67 / 176

background image

4-1

Models 947, 948 and 960 Leak Detectors Operations and Service Manual

Section 4. Maintenance

Like other sensitive test equipment, a mass spectrometer leak detector requires periodic
maintenance to ensure continued reliable operation. After prolonged use, the leak detector
accumulates contaminants from even the cleanest of products tested. These contaminants
eventually impair operation. A thorough disassembly and cleaning of the entire vacuum
system, which includes the cal leak valve block and spectrometer tube, restores normal
operation. For heavy production use, more frequent overhauls are needed. In most cases,
this work is done by user maintenance personnel, but it may also be done by Varian
Vacuum Technologies under the terms of a service contract.

This maintenance section does not cover overhaul of the entire vacuum system. It does
cover daily maintenance and as-required maintenance.

Important Reminders

Heed the following notes, cautions, and warnings when performing maintenance.

WARNING

Disconnect power from the 947/948/960 before performing any
maintenance procedure that requires physically disconnecting
any part of the system.

WARNING

The mechanical components of leak detectors are typically
cleaned with alcohol or other solvents. When heated, sprayed,
or exposed to high-temperature equipment, these solvents
become flammable and explosive, causing serious injury or
death. Do not use near a high-temperature source. Ventilate
the work area with a blower and use solvents only in large,
well-ventilated rooms.

Alcohol and other solvents are irritants, narcotics, depressants,
and/or carcinogens. Their inhalation and/or ingestion may
produce serious effects. Prolonged or continued contact with
the skin results in absorption through the skin and moderate
toxicity. Always ensure that cleaning operations are carried out
in large, well-ventilated rooms. Wear eyeshades, gloves, and
protective clothing.

WARNING

The preamplifier is a static sensitive device. Wear a grounding
device while the preamplifier is being handled.

«
...
65
66
67
68
69
...
»

Содержание 948

















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 948

SMARTCAM SNH-1011N

Бренд: Samsung Страницы: 2

Бренд: Eclipse Страницы: 48

Бренд: Eclipse Страницы: 52

Бренд: Eclipse Страницы: 48

Бренд: Olympus Страницы: 374

Бренд: Olympus Страницы: 66

Бренд: LaserLine Страницы: 68

Бренд: Digital Watchdog Страницы: 2

Бренд: Datavideo Страницы: 136

Бренд: Velleman Страницы: 58

Бренд: ICP DAS USA Страницы: 96

Бренд: Abus Страницы: 18

Бренд: Abus Страницы: 11

Бренд: Konlen Страницы: 9

Бренд: Velocity Страницы: 2

Бренд: UltraSecure Страницы: 2

Бренд: Velleman Страницы: 19

L15LD420 SERIES

Бренд: Lorex Страницы: 170

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды