Vaisala MGP261 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 90

background image

More Information

‣

Configuring Analog Outputs with Insight (page 40)

2.2.4 Installation Type

MGP261 can be installed either directly into the process (for example, through a flange or ball
valve in the actual process pipeline), or using a flow-through adapter (for example, in a
sampling line installation or when performing a field calibration).

MGP261 uses different internal calculation models depending on the installation type and gas
flow rate. For this reason, the type of the installation must be set correctly in MGP261 settings.
You can view and change the installation type configuration with Vaisala Insight PC software:
for instructions, see

Installation Type Configuration in Insight (page 33)

.

Always ensure that the installation type configuration is set

correctly in Insight when changing from one installation type to another, so that
the calculation model in use matches the installation environment and
measurement accuracy is not affected.

CAUTION!

2.2.5 Process Flow Range and Installation Type

A process flow range of 2 ... 20 m/s is suitable for the in situ installation calculation model.
When operating the probe in a low flow environment (0 … 2 m/s) or using the flow-through
adapter, use the flow-through calculation model. To set the correct calculation model for the
flow range, choose the installation type in the Vaisala Insight PC software.

Process Flow Range

Installation Type Selection in Insight PC Software

2 ... 20 m/s

Directly in process

0 … 2 m/s or with flow-through adapter

Flow-through adapter

More Information

‣

Installation Option: Ball Valve Installation (page 22)

‣

Installation Option: Flow-Through Adapter Installation (page 23)

‣

Installation Type Configuration in Insight (page 33)

‣

Connecting to Insight Software (page 35)

‣

Specifications (page 62)

2.2.6 Connectivity to Vaisala Insight Software

The probe can be connected to Vaisala Insight software using a Vaisala USB cable (order code:

257295). With the Insight software, you can:

• Calibrate and adjust the measurement.

• See device information and status.

Chapter 2 – Product Overview

11

«
...
11
12
13
14
15
...
»

Содержание MGP261



























































































Отзывы:

Нет отзывов

Похожие инструкции для MGP261

Бренд: Parr Instrument Страницы: 110

Бренд: Magnet-physik Страницы: 32

Бренд: OHAUS Страницы: 71

Бренд: Bahco Страницы: 21

Бренд: Kübler Страницы: 72

Photo Research PR-810

Бренд: Jadak Страницы: 120

Бренд: Hanna Instruments Страницы: 2

Smart Photometer System iDip 570

Бренд: eXact Страницы: 16

EnviroAlert EA200

Бренд: Winland Страницы: 3

Бренд: Maxtec Страницы: 13

Бренд: BC Biomedical Страницы: 9

MLS 50-3...N series

Бренд: KERN Страницы: 16

Radon Scout Home

Бренд: SARAD Страницы: 2

Бренд: AL Страницы: 2

Бренд: HEIDENHAIN Страницы: 28

Бренд: IMI Hydronic Страницы: 48

Бренд: OfiTE Страницы: 6

Бренд: Zamel Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды