Vaisala MGP261 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 90

background image

7.1.3 Compensation Mode During Calibration

When you start to calibrate the probe with Insight, the probe enters calibration mode, and the
compensation mode is automatically switched to

Setpoint

. In this compensation mode, you

must enter the conditions of your calibration environment as temporary setpoint values in the

Compensation setpoints

tab of the calibration menu.

When you exit calibration mode, the values you have entered in the

Compensation setpoints

tab remain in use as the current setpoint values, but the compensation mode switches back to
the selection that was in place before starting calibration (either

Off

,

Setpoint

,

Measured

, or

External

).

More Information

‣

Configuring Environmental Compensations with Insight (page 44)

7.2 Configuring Environmental Compensations

with Modbus

The Modbus implementation of MGP261 includes configuration registers for pressure and
temperature compensation setpoints. You can also configure the temperature and pressure
compensation mode (

External

,

Setpoint

,

Measured

(temperature only), or

Off

).

For a description of MGP261 Modbus registers, see

Modbus Registers (page 68)

More Information

‣

Modbus (page 38)

‣

Modbus Registers (page 68)

7.3 Configuring Environmental Compensations

with Insight

Using Insight, you can configure the following temperature and pressure compensation

settings:

• Temperature or pressure compensation mode (select the source where the compensation

value is received from)

• The setpoint values for temperature or pressure compensation

• The scaling of the analog input channel (

Analog input 1

) that is used to receive

temperature or pressure values from an external sensor.

Figure 21 (page 45)

describes the different environmental compensation selections in Insight.

MGP261 User Guide

M212273EN-A

44

«
...
44
45
46
47
48
...
»

Содержание MGP261



























































































Отзывы:

Нет отзывов

Похожие инструкции для MGP261

Бренд: Kanomax Страницы: 2

Бренд: Keithley Страницы: 156

SXNP10 - DIGITAL PIANO

Бренд: Panasonic Страницы: 63

Бренд: Camille Bauer Страницы: 62

Бренд: Hach Страницы: 145

Бренд: Hach Страницы: 358

Polymetron 9582sc

Бренд: Hach Страницы: 280

Бренд: HACH LANGE Страницы: 15

Бренд: Vectronics Страницы: 4

Бренд: Yamaha Страницы: 12

Бренд: LEM Страницы: 33

Бренд: Toro Страницы: 60

ACCURE 2350-GAS

Бренд: ROOTECH Страницы: 26

Бренд: THORLABS Страницы: 49

Бренд: Tohnichi Страницы: 12

Бренд: OrienTek Страницы: 2

Бренд: ATIM Страницы: 25

Бренд: Baron Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды