Vaisala MGP261 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 90

background image

3.1.4 Installation Option: Ball Valve Installation

The following figure

shows an example MGP261 ball valve installation. The figure highlights

the correct

wiring routes and shows the recommended installation depth and orientation.

Always use a separate cable for the optional (Ex ia) external

pressure or temperature sensor input wiring (1), and make sure the wiring

remains separated from the terminals and wiring (2) on the other side of the
metal barrier (3) on the component board.

CAUTION!

1

2

4

3

5

Figure 8 MGP261 Installation Example with Wiring Routes and Recommended Orientation and

Depth

1

Optional external pressure or temperature sensor input wiring (Ex ia): use the M16x1.5
lead-through and route the cable directly to the terminal.

2

Standard analog output, power supply input, and RS-485 communication wiring: use the
M20x1.5 lead-throughs and route the cables to the terminals through the openings below
the component board.

3

Metal barrier separating the intrinsically safe external sensor input terminals (optional, for

environmental compensation input) from the analog output, power supply input, and
RS-485 terminals on the component board.

4

1.5" male NPT thread on MGP261:

never install to any other thread type than 1.5" female

NPT

.

5

For best results, install MGP261 horizontally and position the tip of the filter within 1/3 of

the pipe's diameter from the pipe centerline. In smaller pipes, the installation depth can be
adjusted by using an adapter (for example, a ball valve).

More Information

‣

Recommended Installation Position on Pipeline (page 24)

MGP261 User Guide

M212273EN-A

22

«
...
22
23
24
25
26
...
»

Содержание MGP261



























































































Отзывы:

Нет отзывов

Похожие инструкции для MGP261

Surface Scatter 7 sc

Бренд: Hach Страницы: 6

Бренд: Hach Страницы: 118

Бренд: Hach Страницы: 388

Orbisphere 51 Series

Бренд: Hach Страницы: 118

ORBISPHERE 3650 Atex

Бренд: Hach Страницы: 51

Бренд: Hach Страницы: 72

POLYMETRON 8362

Бренд: Hach Страницы: 78

Pocket Colorimeter II

Бренд: HACH LANGE Страницы: 146

Бренд: Hach Страницы: 146

Бренд: Hach Страницы: 36

PHOSPHAX indoor sc

Бренд: Hach Страницы: 104

Lange ORBISPHERE 3100

Бренд: Hach Страницы: 384

Бренд: Hach Страницы: 172

Бренд: YOSensi Страницы: 3

Бренд: Lasertec Страницы: 21

Бренд: X-laser Страницы: 17

Бренд: Vectronics Страницы: 4

Бренд: Danfoss Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды