Vaisala MGP261 Скачать руководство пользователя страница 47

Страница: 47 / 90

Figure 21

Measurement

Menu View in Insight PC Software

Compensation power-up defaults

: configure the setpoint compensation values that are

taken into use at device reset. Used when the temperature or pressure compensation
mode is set as

Setpoint

Compensation setpoints

: configure the temporary setpoint compensation values that are

in use while the device is powered on, but revert back to power-up defaults when the
device is reset. Used when the temperature or pressure compensation mode is set as

Setpoint

Measurement

(shown in figure): configure the pressure and temperature compensation

modes (available options:

Setpoint

External

Measured

(temperature only), and

Off

Analog input 1

: configure the input from the external pressure or temperature sensor

(used when the pressure or temperature compensation mode is set as

External

1. Connect to Insight (see

Connecting to Insight Software (page 35)

2. Select

> Configure Device

3. Select one of the compensation modes in the

Measurement

menu.

4. See the separate instructions for configuring the compensations in each compensation

mode:

•

Configuring Setpoint Values for Compensations with Insight (page 46)

•

Using Probe Measurement as Temperature Compensation (page 46)

•

Using Compensation Received from External Temperature or Pressure Sensor

(page 46)

•

Configuring Input from External Analog Pressure or Temperature Sensor (page 47)

More Information

‣

Compensation Mode During Calibration (page 44)

Chapter 7 – Environmental Compensation

Содержание MGP261



























































































Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды

Vaisala MGP261, Руководство пользователя

Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды