Vaisala MGP261 Скачать руководство пользователя страница 63

Страница: 63 / 90

3. Clean the probe with running water and a cloth. Standard cleaning agents can be used.

Do not clean the probe with a pressure washer.

CAUTION!

Do not immerse the probe in liquid to clean it.

CAUTION!

4. To install the probe back into the process after cleaning, follow the installation instructions

starting from

Preparing Probe for Installation (page 26)

5. If you are sending the probe to Vaisala for maintenance, allow it to dry fully before

packing it. See the instructions in

Sending Probe to Vaisala (page 61)

9.4 Sending Probe to Vaisala

If you need to return the probe for maintenance or replacement, contact Vaisala technical
support.

Do not ship the probe to Vaisala without contacting technical

support. Technical support will provide you with return authorization and up-to-
date shipping instructions.

CAUTION!

1. Read the warranty information.

2. Contact Vaisala technical support and request a Return Material Authorization (RMA) and

shipping instructions.

For information on product warranties, technical support, and repair services,
see

www.vaisala.com/support

Always request the RMA before returning any material to Vaisala.

3. Follow the return instructions received from Vaisala technical support. When packing the

probe for shipping, ensure that you use sufficient padding, the probe has dried

completely after cleaning, and that the probe is tightly sealed in a plastic bag.

Chapter 9 – Maintenance

Содержание MGP261



























































































Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды

Vaisala MGP261, Руководство пользователя

Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды