Vaisala MGP261 Скачать руководство пользователя страница 28

Страница: 28 / 90

3.2 Preparing Probe for Installation

The following tools are required when installing:

• Adjustable wrench (or a similar suitable tool) for turning the tightening nut

• Connection box key (provided)
• Input and output cables for wiring
• Small slotted screwdriver for screw terminals

• PTFE tape (wide) for the probe threads

M16x1.5 (1)

M20x1.5 (2)

PTFE

1. Attach cable glands (not provided by Vaisala) to the wiring lead-throughs as required.

Note the cable gland requirements listed in

Guidelines for Safe Use in Hazardous

Conditions (page 17)

). For more information on cable gland options and lead-through

dimensions, see

Cable Gland Options and Lead-Throughs (page 14)

• Use an M16x1.5 gland for the optional external sensor input wiring (Ex ia).

• Use 1 or 2 M20x1.5 glands for wiring the 4 … 20 mA analog output, power supply input

and RS-485 terminals (as required in your application).

• Seal unused lead-throughs.

2. Apply PTFE tape on the probe threads.

• Inspect the threads and remove any possible dirt.

• Wrap 2-3 revolutions of tape in the direction of the thread spiral, starting from the

first thread. Keep the edge of tape parallel to the face of the thread while wrapping.

• Do not tape beyond the edge of the threads or leave loose tape hanging.

The correct thread type in which to install MGP261 is

1.5"

female NPT

. Installing into any other thread type can damage the

equipment and compromise the leak tightness of the connection. If unsure,
verify the thread type with the NPT 1.5" thread test plug.

CAUTION!

MGP261 User Guide

M212273EN-A

Содержание MGP261



























































































Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды

Vaisala MGP261, Руководство пользователя

Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды