Vaisala MGP261 Скачать руководство пользователя страница 43

Страница: 43 / 90

1. Connect to Insight (see

Connecting to Insight Software (page 35)

2. Select

> Configure Device

, and then one of the 3 analog outputs.

3. Select the measurement parameter that is sent on the output channel you are configuring,

set the scaling for the output, and define the output level that indicates an error.

4. Store the selections with

Save

and exit with

Close

5. Repeat the configuration for each output (analog outputs 1, 2, and 3) as required.

More Information

‣

Wet Basis and Dry Basis Measurement Parameters (page 42)

6.4 Changing Units in Insight

Figure 19 Unit Selection in Insight

You can change the units of parameters (for example, metric or non-metric temperature) in

the

Unit Settings

menu in Insight.

1. Connect to Insight (see

Connecting to Insight Software (page 35)

Chapter 6 – Analog Output Configuration

Содержание MGP261



























































































Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды

Vaisala MGP261, Руководство пользователя

Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды