Vaisala MGP261 Скачать руководство пользователя страница 34

Страница: 34 / 90

5. After tightening the probe gland, tighten the 2 screws on the clamp.

A high process pressure can cause the probe to detach from

the adapter if the clamp and gland have been left loose. Always fully
tighten the clamp and probe gland.

WARNING!

6. Attach the mounting plate to the mounting surface with screws or ties. For mounting

plate dimensions, see

Figure 30 (page 67)

7. Check that the probe sits closely in the clamps after mounting. The mounting kit and the

flow-through adapter have been aligned so that the probe sits in the adapter in a straight
angle. A gap between the probe body and clamp indicates that the mounting alignment is
incorrect and must be adjusted.

90°

Ensure the adapter mounting does not pull the probe out of a

straight angle. If the mounting pulls the probe to the side, the leak
tightness of the gland O-ring can be affected.

CAUTION!

8. Connect the gas inlet tube to the upper port of the adapter and the gas outlet tube to the

lower port. Adapter port size: G 1/8.

9. Connect to Vaisala Insight PC software and ensure that the installation type has been set

Flow-through adapter

. For instructions, see

Installation Type Configuration in Insight

(page 33)

More Information

‣

Installation Type (page 11)

‣

Installation Option: Flow-Through Adapter Installation (page 23)

‣

Installation Type Configuration in Insight (page 33)

‣

Flow-Through Adapter Dimensions (page 67)

MGP261 User Guide

M212273EN-A

Содержание MGP261



























































































Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды

Vaisala MGP261, Руководство пользователя

Результаты поиска

Содержание MGP261

Отзывы:

Похожие инструкции для MGP261

Бренды по названию

Популярные бренды