UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 38 / 88

9.1

Fill Boiler With Water And Purge Air

• Flush heating system, including all heating zones.
• Fill boiler with potable water.

• Fill boiler and system piping with water (or

antifreeze-water solution, if used). See antifreeze

information page 14. Purge air from boiler using air

vent. Purge air from system piping.

• Close air vent after all air is purged from both boiler

and system piping.

• Inspect system piping and boiler connections. Repair

any leaks immediately.

• Activate all heating zones and calls for heat,

including CH calls and DHW calls (if available).

•

Close manual gas shut off valve. Let system run for

30 minutes. When boiler goes into lockout, reset

boiler by pressing "Reset" button until boiler resets.

•

Do not open gas shutoff valve until all air is purged

from system.

9.2

Fill Condensate Trap with Water

• Disconnect spring tension clip from condensate hose

barb. See figure 9-1.

• Disconnect tubing below from hose barb.
• Pour approximately 2 cups (473 ml) of water into

condensate drain.

• Reconnect tubing to hose barb with spring tension

clip. See figure 9-1.

FIGURE 9-1 Condensate Drain Assembly

Reconnect hose to hose

barb with spring tension clip

before starting boiler.

Disconnect spring tension

clip from hose barb and fill

Condensate trap with water.

9 - START UP PROCEDURE

Note

Condensate trap must be manually filled with water

at initial start up.

Note

To maintain boiler efficiency and prevent boiling
inside the heat exchanger, flush entire heating

system until clean.

150-299 MBH shown

50-100 MBH shown

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды