UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 7 / 88

Information and specifications outlined in this manual in effect at the

time of printing of this manual. reserves the right to

discontinue, change specifications or system design at any time without

notice and without incurring any obligation, whatsoever.

2 - INTRODUCTION

2.4

Designated Use

•  Hot water heating boiler.
•  Indoor installation.
•  Closet or alcove installation.
•  Direct vent boiler.
•

For use with natural gas or liquefied petroleum gases

(LP/propane).

2.5

The unit MUST NOT:

• Directly heat potable water. Indirect heating is acceptable.
• Heat water with non-hydronic heating system chemicals

present (example, swimming pool water).

• Exceed 150 psig (1.03 MPa) maximum allowable working

pressure.

• Exceed 195°F (90.5°C) system design temperature.

2.6

Operational Features

• Modulating: 20-100%.
• Integral Dual Limit.
•

Integral Low Water Cutoff (with test button).

•  Outdoor Temperature Reset.
•  Integral Multiple Boiler Control.
•  Heat exchanger over heat protection.

2 - INTRODUCTION

2.1

Installation shall conform to requirements of authority

having jurisdiction or in absence of such requirements:

• United States

• National Fuel Gas Code, ANSI Z223.1/NFPA 54.
• National Electrical Code, NFPA 70.

2.2

Where required by authority having jurisdiction,

installation shall conform to Standard for Controls and Safety

Devices for Automatically Fired Boilers, ANSI/ASME CSD-1.

Additional manual reset low water cutoff may be required.

2.3 Requirements for Commonwealth of Massachusetts:

Boiler installation must conform to Commonwealth of

Massachusetts code 248 CMR which includes but is not limited

to:

Installation by licensed plumber or gas fitter.

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды