UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 47 / 88

11.2

Annual Shut Down Procedure

•

Follow instructions “To Turn Off Gas To Appliance”

unless

boiler is also used to supply domestic hot water. See

section 10.

• Drain system completely if system does not have antifreeze

when heating system is to remain out of service during

freezing weather.

• Drain condensate lines when boiler is to be exposed to

freezing temperatures.

WARNING

Following service procedures must be performed

by qualified service agent. Boiler owner shall not

attempt these steps. Failure to do so could result in

death or serious injury.

11.3

Annual Inspection and Cleaning of Boiler

Components

• Obtain Burner Inspection Kit. Follow kit instructions to

prepare for examination and cleaning.

• Burner and heat exchanger inspection and cleaning:

Remove gasket and burner. Allow burner to clear

top lip of chassis.

Remove any residual sleeve and/or gasket material

from removed burner.

Clean burner using air hose directed into top of

burner opening to dislodge any debris in burner

ports. Inspect burner for foreign matter in flame

ports or inside burner. Remove foreign matter

by blowing with compressed air or vacuuming.

Replace burner if it cannot be cleaned or is showing

deterioration.

Clean heat exchanger with low pressure water

spray. Use flexible handle nylon brush to loosen

sediment and oxide on all accessible heating

surfaces of heat exchanger. Take care not to get

brush stuck in heat exchanger.

Remove any remaining loosened sediment using

shop vacuum with snorkel attachment.

•

Clean condensate collector if significant debris found in heat

exchanger.

Expand upper spring tension clip of condensate trap

using hose clamp pliers. Disconnect condensate trap

from condensate collector. See figure 9-1.

Disconnect wire harness from vent temperature

sensor. See figures 3-4 & 3-5 .

Loosen upper hose clamp securing condensate

collector to flue pipe using 3/8" socket with 6"

extension.

11 - GENERAL MAINTENANCE AND CLEANING

• Circulator pump and combustion air blower motor furnished

with boiler are permanently lubricated from factory and

require no further lubrication. Lubricate field sourced

pumps and/or motors according to pump and/or motor

manufacturer’s instruction.

• Check following components are operating properly and are

free of blockages or obstructions:

• air vent;
• check venturi air inlet for blockage and clean as

required;

• verify pressure test port cap and combustion test port

are in place;

• return temperature sensor clip must be securely seated

on pipe; Check boiler for any sign of leaks.

•

Check low water cutoff using user interface.

• Check operation by pressing test button on low water

cutoff.

• "Low Water" LED should illuminate and burner

should shut down.

• Should get error message on User Interface (E36).

•

Every 5 years remove low water cutoff. Reinstall after

cleaning.

•

Every 10 years replace low water cutoff.

•

See Table 13 page 40 for flame signal rate at 100% firing

rate ( High fire).

•

Visual inspection of flame through sight glass. Burner should

be fully illuminated. See

figures 11-1 & 11-2.

• Check heating system expansion tank.

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды