UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 13 / 88

4 - LOCATING BOILER

CAUTION

Boiler weight exceeds 75 pounds (34 kg). Do not lift

boiler onto wall without assistance.

4 Slots for attaching

Wall Mount Bracket to

Studs

Center brackets. Avoid overhang on sides of wall

mount bracket.

FIGURE 4-3 Low Water Cutoff Orientation

5° ~ 15°

Factory

Default 10°

WARNING

Fire, explosion hazard. Mount boiler vertically or

slightly tilted backward to insure proper function of

low water cutoff. Failure to follow these instructions

could result in death or serious injury.

4.2

Pre-pipe supply and return water connections with factory

fittings before wall mounting.

4.3

Wall Mounting

Mount boiler on wall using wall mounting bracket included

with unit.

• Structure must be capable of supporting boiler weight

plus 60 lbs (28 kg). See Table , page 4.

• Wall mount bracket has 4 slots allowing mounting on

two (2) wall studs spaced at 11½" to 16½" on center.

See figure 4-2.

• Boiler includes (4) 3/8" x 3" lag screws and (4)

washers for attaching wall mount bracket to wood

studs. Field source appropriate fasteners for other wall

constructions (masonry, concrete).

• Attach wall mount bracket level on wall.

• Boiler must engage with wall mount bracket.

• Avoid overhang on sides of wall mount bracket. Verify

boiler bracket is centered on wall bracket. See figure

4-2.

• When mounting boiler onto wall insert two plastic

stoppers and two plastic plugs to packaging holes on

back of boiler. See parts listed on page 2.

• Mount boiler vertically or slightly tilted backward to

insure the low water cutoff functions properly. See

figure 4-3 for low water cutoff orientation.

Note

Lift boiler using chassis. Using front jacket, vent

piping, water or gas fittings to lift boiler may cause

damage to the boiler.

Use two (2) wrenches when tightening and fitting to
pipe boiler's threaded fittings. Boiler's internal piping

can be damaged if subjected to excessive torque.

Note

FIGURE 4-2 Wall Mount Bracket Engaged with

Bracket on Boiler

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды