UTICA BOILERS UBSSC-050 Скачать руководство пользователя

Страница: 15 / 88

WARNING

Burn and scald hazard. Safety relief valve could

discharge steam or hot water during operation.

Install discharge piping per these instructions.

FIGURE 5-2 Safety Relief Valve Discharge Piping

Safety Relief Valve

5 - HYDRONIC PIPING

5.3 Safety Relief Valve and Air Vent

•

Install safety relief valve and air vent using pipe fittings

provided with boiler. See figure 5-1

• Install safety relief valve with spindle in vertical position.
•

Do not install shutoff valve between boiler and safety

relief valve.

• Install discharge piping from safety relief valve. See

figure 5-2.

• Use ¾" or larger pipe.
• Use pipe suitable for temperatures of 375°F (191°C) or

greater.

• Individual boiler discharge piping shall be independent

of other discharge piping.

• Size and arrange discharge piping to avoid reducing

safety relief valve relieving capacity below minimum

relief valve capacity stated on rating plate.

• Run pipe as short and straight as possible to location

protecting user from scalding and properly drain piping.

• Install union, if used, close to safety relief valve outlet.
• Install elbow(s), if used, close to safety relief valve

outlet and downstream of union (if used).

• Terminate pipe with plain end (not threaded).

Check Local Codes For

Maximum Distance To

Floor

[50-100 Size Shown]

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды