UTICA BOILERS UBSSC-050 страница 72 Скачать руководство пользователя

Страница: 72 / 88

• PURGE

- To free gas conduit of air or gas, or mixture of gas

and air.

• PURGE TIME

- Period of time intended to allow for

dissipation of any unburned gas or residual products of

combustion.

• QUALIFIED AGENCY

- Any individual, firm, corporation, or

company engaged in and responsible for:

• Installation, testing, or replacement of gas piping, or

connection, installation, testing, repair or servicing

of appliances and equipment.

• Experienced in such work.

• Familiar with all precautions required.

• Complies with all requirements of authority having

jurisdiction.

• SAFETY RELIEF VALVE

- Valve designed to relieve

pressure in hot water supply system when pressure exceeds

pressure capability of equipment.

• SAFETY SHUTOFF DEVICE

- Device that will shut off gas

supply to controlled burner in event source of ignition fails.

• SEDIMENT TRAP

- Gas piping arrangement designed to

collect any liquid or solid contaminant before reaching gas

valve.

• VENT

- Passageway used to convey flue gases from

appliance vent connector to outdoors.

• VENTING SYSTEM

- Continuous open passageway from

of appliance vent connector to outdoors for purpose of

removing flue or vent gases.

15 - GLOSSARY

PN 240011320 Rev. G 10/01/2021]

Содержание UBSSC-050

























































































Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды

UTICA BOILERS UBSSC-050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание UBSSC-050

Отзывы:

Похожие инструкции для UBSSC-050

Бренды по названию

Популярные бренды